To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 23784 (-10)
  Re: caster wheel design
 
(...) This the one you mean? (URL) (22 years ago, 31-Mar-05, to lugnet.robotics)
 
  Re: caster wheel design
 
(...) You can actually do that one better - use a 2x2 plate with offset wheel holder on the bottom, & you can dispense with the 2x3 plate. I browsed Peeron & Bricklink and couldn't locate it, but they're handy for microcasters. (22 years ago, 31-Mar-05, to lugnet.robotics)
 
  Re: Alternate connectors
 
You even do not need to cut your existing LEGO wires visit (URL) cost effective too Nitin (...) (22 years ago, 30-Mar-05, to lugnet.robotics, FTX)
 
  Re: Alternate connectors
 
(...) One of the NALUG members did the very thing you are talking about. I believe he used a connector from Radio Shack but I will double check or have him check the forums. Mike (22 years ago, 30-Mar-05, to lugnet.robotics, FTX)
 
  Alternate connectors
 
I am trying to find a suitable connector that will let me cut up and extend the regular mindstorm wires, as well as to connect to custom built sensors. I have seen that some people have used (URL) Molex connectors> (URL) but I can't seem to find (...) (22 years ago, 30-Mar-05, to lugnet.robotics, FTX)
 
  Re: caster wheel design
 
(...) Another "microcaster" is the style used in "ERBIE the Robocar" discussed here (URL) made with a 2x2 turntable, a 2x3 plate, and a single wheel (URL) works surprisingly well, so long as 1) The weight isn't huge and 2) the surface isn't too (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
 
  Re: caster wheel design
 
(...) Move the other wheels or the CG so that the caster doesn't support much weight. No matter what your design, a caster that carries a lot of weight will not work well. The large turntables will have a lot of friction when carrying a lot of load. (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
 
  Re: I2C bus for Lego RCX
 
OK, that's neat! That's a novel way to attach to bricks and electrical connectors. Is the $36 before or after the $10 discount ? Either way, I'll probably be buying one to play with. -JSM (...) (22 years ago, 29-Mar-05, to lugnet.robotics)
 
  Re: caster wheel design
 
If you are planning on running on smooth surfaces, you might be suprised at how well your robot drives and turns with just one of those domed 2x2 'gliders' instead of a wheeled caster. ---...--- Steve Baker ---...--- HomeEmail: (...) (22 years ago, 30-Mar-05, to lugnet.robotics)
 
  Re: caster wheel design
 
(...) How heavy is this? A caster needs an offset, but making this offset as small as possible should reduce bending. I usually use a medium pulley on a #3 axle; either end of the axle is held in the pin hole of a Technic crossblack, while short (...) (22 years ago, 30-Mar-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR