 | | Re: The Great Ball Contraption
|
|
news-gateway@lugnet.com wrote on 01/10/2005 01:03:08 PM: (...) little (...) beyond 32 studs can be used as right-turns. It's just as obvious (once Steve points it out, that is) that modules that do *not* extend into the first 32 studs (besides the (...) (22 years ago, 11-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
Russell Nelson <nelson@crynwr.com> wrote on 01/10/2005 12:03:04 PM: (...) Or specify that the input bin must have a technic beam at the front edge of the input bin to accept technic pins: this is very similar to how the castle walls connect... Tim (...) (22 years ago, 11-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) That's really not true. As a module builder, you can make all the turns you want. This one makes a whole bunch: (URL) you can't figure out how to put the output in the correct place, with respect to the input, that's not a problem with the (...) (22 years ago, 11-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
"Steve Hassenplug" <Steve@TeamHassenplug.org> wrote in message (...) Yes. Currently it's not being able to make turns in both directions with the hopper feed setup the way it is. Someone did point out that there would be a lot of wasted space if (...) (22 years ago, 11-Jan-05, to lugnet.robotics)
|
| |
 | | RE: The Great Ball Contraption
|
|
<SNIP> (...) There is only one layout, strictly using the current rules, that a self sustaining layout can be achieved: XXX...XXX X X XXX...XXX And, the balls would be traveling clockwise in the layout. Note, that given the current basic rules, (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) I didn't think about this until lunch, but you'll note this little yellow modules conforms to the spec, and works very well as an 90 degree turn to the left, and could also turn right: (URL) fact, it may be interesting to see someone build a (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) That's a good idea, which I don't think has been suggested, yet. However, that sort of requires a module to have corner studs... :) This module mostly uses liftarms: (URL) it turns out, I suspect 90% of the modules will not require (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
Steve Hassenplug writes: > (URL) notice that the spec says "Currently, there is no standard for physically connecting modules together." One possibility is for a module to grab onto the two corner studs of the input bin of the module to the right, (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Why impose more limits than necessary? Of the 10 modules in our (very successful) test GBC, these 4 would have to be eliminated for being out-of-spec: (not a multiple of 32) (URL) I forgot, you can't use 48x48 baseplates. Add this: (URL) to (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Wow. Mondayness for me as well. I agree with you, Rob. That said, to start, Steve and Co. have their little thing goin' on, and I just wanted to point out that, within the parameters as layed out by them, one has toe potential to make a module (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
"David Koudys" <dkoudys@redeemer.on.ca> wrote in message news:IA3zL9.xKJ@lugnet.com... (...) What's the big deal? Either you can make a module to comply with simple specs, or you can't. If you need more space and can't fit everything inside 1 - (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) <snip> (...) I love standards, but I also like the 'variedness' of the GBC modules--trying to get somethign specific hammered down, like 'only 32x32 baseplates with the bin in the bottom left corner' might be a little difficult. As it is, (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | RE: The Great Ball Contraption
|
|
<SNIP> (...) Personally, I think something similar to the moonbase concept should be applied--an input bin with opening or edge at a given heighth and width and placed in a specifica location on a standard footprint size, or perhaps by allowing (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) I completely agree with that assessment. However, the premise is that I'm using a 32x32 baseplate with the hopper in the bottom left hand corner--using that premise, the module can be used either in-line, or 90 degrees. If one does not use the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
news-gateway@lugnet.com wrote on 01/10/2005 10:01:48 AM: (...) thus the (...) module, (...) or 90 (...) That assumes that there is nothing in front of the hopper. There is nothing to say that you are limited to a module 32 studs deep. If you choose (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | RE: TGBC - The Weakest Link?
|
|
<SNIP> (...) Like a train layout, how about routing/switching module to create multiple ball routes? This way, if any one module acts up, only modules affected in that path need to be dealt with. Given the standards (regarding input/output bin (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Not to oversimplify, but I mean if the 'standard' for the ball contraption is 32 studs from the front of the hopper to the back edge of the baseplate, and thus I personally would probably grab a 32 x 32 stud baseplate to build on, thus the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Is there something that a module builder can not do because the standard is too simple? Steve (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
Steve Baker writes: > So simply write into the rules that everyone who submits a left hand > turn has to submit a corresponding right hand turn or they won't > be accepted. Excellent idea! But it's even easier than that!! Do NOT change the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
tmassey@obscorp.com writes: > Or not: leave the standard as it is (except for specifying that the space > above the input belongs to the previous module), and have the organizers > build (or specificially request) out-of-spec modules to accomplish (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|