To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 23319 (-10)
  Re: The Great Ball Contraption
 
news-gateway@lugnet.com wrote on 01/10/2005 01:03:08 PM: (...) little (...) beyond 32 studs can be used as right-turns. It's just as obvious (once Steve points it out, that is) that modules that do *not* extend into the first 32 studs (besides the (...) (22 years ago, 11-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
Russell Nelson <nelson@crynwr.com> wrote on 01/10/2005 12:03:04 PM: (...) Or specify that the input bin must have a technic beam at the front edge of the input bin to accept technic pins: this is very similar to how the castle walls connect... Tim (...) (22 years ago, 11-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) That's really not true. As a module builder, you can make all the turns you want. This one makes a whole bunch: (URL) you can't figure out how to put the output in the correct place, with respect to the input, that's not a problem with the (...) (22 years ago, 11-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
"Steve Hassenplug" <Steve@TeamHassenplug.org> wrote in message (...) Yes. Currently it's not being able to make turns in both directions with the hopper feed setup the way it is. Someone did point out that there would be a lot of wasted space if (...) (22 years ago, 11-Jan-05, to lugnet.robotics)
 
  RE: The Great Ball Contraption
 
<SNIP> (...) There is only one layout, strictly using the current rules, that a self sustaining layout can be achieved: XXX...XXX X X XXX...XXX And, the balls would be traveling clockwise in the layout. Note, that given the current basic rules, (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) I didn't think about this until lunch, but you'll note this little yellow modules conforms to the spec, and works very well as an 90 degree turn to the left, and could also turn right: (URL) fact, it may be interesting to see someone build a (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) That's a good idea, which I don't think has been suggested, yet. However, that sort of requires a module to have corner studs... :) This module mostly uses liftarms: (URL) it turns out, I suspect 90% of the modules will not require (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
Steve Hassenplug writes: > (URL) notice that the spec says "Currently, there is no standard for physically connecting modules together." One possibility is for a module to grab onto the two corner studs of the input bin of the module to the right, (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Why impose more limits than necessary? Of the 10 modules in our (very successful) test GBC, these 4 would have to be eliminated for being out-of-spec: (not a multiple of 32) (URL) I forgot, you can't use 48x48 baseplates. Add this: (URL) to (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Wow. Mondayness for me as well. I agree with you, Rob. That said, to start, Steve and Co. have their little thing goin' on, and I just wanted to point out that, within the parameters as layed out by them, one has toe potential to make a module (...) (22 years ago, 10-Jan-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR