To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 22729 (-10)
  Re: Competitive MINDSTORMS - at Sumo-bot 6?
 
(...) David, It would be nice to meet you, and see your robots at Sumo-bot 6 (on Sept 18th). It sounds like you don't have enough pieces to build them all at the same time (along with anything else you may have built). I suggested to Jona that I (...) (22 years ago, 28-Aug-04, to lugnet.robotics)
 
  electric pneumatic valve actuators?
 
Joe (...) to (...) I have some I was given as a sample by someone who uses them. He said they were "very cheap". but didn't give me a price or supplier. Size is 23x23x45mm, They're single-acting. Probably 12V. The only text on them is PAT123395 (...) (22 years ago, 27-Aug-04, to lugnet.robotics)
 
  Re: electric pneumatic valve actuators?
 
(...) Sounds cool -- that's the sort of thing I had in mind, though I couldn't find solenoid valves for less than $70 or so, which is just too much. A reasonable price in my book would be something like $10 per valve, or if it's already adapted for (...) (22 years ago, 27-Aug-04, to lugnet.technic, lugnet.robotics)
 
  Re: electric pneumatic valve actuators?
 
(...) This is the most likely *IMHO* as there are medical clamps that do this, and they are (magically) operated like a screw clamp. All that remains is connecting the device to LEGO pieces so a motor can activate the clamp open/closed. I haven't (...) (22 years ago, 26-Aug-04, to lugnet.robotics)
 
  Re: electric pneumatic valve actuators?
 
(...) What do you feel is a reasonable price? In the next week or two I should have the first prototype built of a pair of commercial solenoid valves adapted for LEGO/RCX usage. They'll be 9v, and around 1.1 watts. It will be 2 3-way valves, one for (...) (22 years ago, 26-Aug-04, to lugnet.technic, lugnet.robotics)
 
  electric pneumatic valve actuators?
 
I've been thinking a lot lately about electrically activated (as opposed to manual) pneumatic valves. I've seen several designs on the net where someone has taken a regular LEGO manual valve, and attached a motor. That's clever, but I'm wondering if (...) (22 years ago, 26-Aug-04, to lugnet.technic, lugnet.robotics)
 
  Re: Steering Drive
 
Hi, I have used this flag technique successfully. It was easier than a hardware solution. I use leJOS which also provides a way to check which direction the motor is turning. When the touch sensor is hit, you can do something like if ( (...) (22 years ago, 26-Aug-04, to lugnet.robotics)
 
  Re: Steering Drive
 
"Jon Gilchrist" <robots@DEELEETEf3p.com> wrote in message news:cmsni0t76f5vr92...4ax.com... (...) I don't understand why you need to know which way to turn the wheels to go straight? When you initialize the robot you can test with low power first (...) (22 years ago, 25-Aug-04, to lugnet.robotics)
 
  Re: Steering Drive
 
(...) Remember to gear down so the axel sets off the sensor say x times per wheel rotation. You should not lose any precision unless you have a poor tapping mechanism. However, you will only have accuracy as good as the touch sensor can go on/off. (...) (22 years ago, 25-Aug-04, to lugnet.robotics)
 
  Re: Steering Drive
 
(...) If you want to do this but don't want to or can't use non-lego parts, Rob Stehlik found that you can create the same effect using lamps: (URL) (22 years ago, 25-Aug-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR