To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 21829 (-10)
  OT Re: Legway and Robolab
 
--- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system ((URL) 6.0.548 / Virus Database: 341 - Release Date: 12/5/2003 (23 years ago, 10-Dec-03, to lugnet.robotics)
 
  Re: Legway and Robolab
 
(...) Apparently, the standard firmware imposes a 100ms delay before a motor can change directions (ostensibly to protect the motors). This might be the source of some of the instability. Dick Swan suggests a possible way around the delay at the (...) (23 years ago, 10-Dec-03, to lugnet.robotics)
 
  Re: Legway and Robolab
 
(...) I spent a couple of evenings with a Legway, EOPD sensors and Robolab. I could not get it to balance or reach any condition of stability. I eventually 'gave up' because I felt that the violent control actions would destroy my motors :) Steve, (...) (23 years ago, 10-Dec-03, to lugnet.robotics)
 
  Product Review: Linksys WVC11B and VEO Observer
 
Hello everyone, I've been fortunate enough to get to play with the Linksys WVC11B Wireless and a VEO Observer Internet Video Cameras. In the event anyone is considering the purchase of a networked camera, perhaps these notes will be of interest to (...) (23 years ago, 9-Dec-03, to lugnet.robotics)
 
  Re: WWW spider
 
yes that was my goal in this schema pixel "Kevin L. Clague" <kevin_clague@yahoo.com> wrote in message news:HpMsDz.vz2@lugnet.com... (...) (23 years ago, 9-Dec-03, to lugnet.robotics)
 
  Re: WWW spider
 
(...) It is a very cool mechanism. Your circuit can change from a 3 piston timer to a four piston timer, right? Kevin (23 years ago, 9-Dec-03, to lugnet.robotics)
 
  Re: WWW spider
 
hi i just developed this sequencer DL (URL) there is no purpose for this mechnism :) it shows 2 things 1. even small and simple changes in the circuit make it a little bit complicated :))) 2. it can be done :) it's just a first trial i'll work on (...) (23 years ago, 9-Dec-03, to lugnet.robotics)
 
  Re: Legway EOPDs
 
(...) Steve, Have you tired using a combination of gears and the rotation sensor as a solution? I know there was some discussion awhile back about the disadvatages of the rotation sensor (not enough resolution) but I have been thinking about this (...) (23 years ago, 9-Dec-03, to lugnet.robotics)
 
  Re: Legway and Robolab
 
(...) While I agree this sounds like a fun project, don't be too disapointed if things don't go as well as you hope. I did some testing with NQC, and I found the standard firmware to be too slow to balance a Legway. I'm not going to say it can't be (...) (23 years ago, 8-Dec-03, to lugnet.robotics)
 
  RE: Legway and Robolab
 
Hello, We have used EOPDs with Robolab. We have not built a Legway. Sounds like a fun project, I will see if the younger family wants to do that over the week and weekend. A home-learning project! Bill -----Original Message----- From: (...) (23 years ago, 8-Dec-03, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR