 | | Re: legOS problem
|
|
I have tried this with brand new batteries.. still the same result.. I am using rcxfirm to send the firmware across to the rcx unit. The download seems to run fine, and ends with a beep from the rcx unit, after this beep the rcx unit shuts down and (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | legos problem solved
|
|
I compiled firmdl for winnt using the cygwin tools and now everything is up and running.. I plan on making all of my binaries for winnt available as soon as I get home from my holidays... Thanks for everyone's help Jonathan (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Mindstorms CD and Soft Windows
|
|
SoftWindows will give you access to the serial port (with a little configuration) so it should work. On an SGI machine you can't run the port over 9600. I'm not sure about Macs. I only worked on the SGI versions of SoftWindows (V1.25 to 95 V1.01). (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Non-standard differential wanted
|
|
Just wanted to let everyone know that I updated my webpage with this design. The page is (URL) It now contains pictures of a robot using the address/subtractor that my father built. His layout of the adder/ subtractor is more efficient (direct drive (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor connectors
|
|
2 pins are power and 2 are ground. It's made that way so the connector can go in several ways. You can reverse motor direction just by turning the power connector at either end. LegoCork@aol.com (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor connectors
|
|
OOoopsss... LegoMajik@aol.com not LegoCork, that's Mindstorms name. Dohh!!! (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | RCX Serial
|
|
I'm embarassed to post with such a trivial discovery, but in the hopes of saving somebody a little time: You can get the serial port to transmit under legOS by doing *((char *)0xffd0) = 0x09; // TCR *((char *)0xffd1) = 0x13; // TCSR *((char (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | R/C Servo to Legos
|
|
Does anyone have a solution for coupling the output of an R/C servo to something like a Lego axel? Thanks. (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
You could glue a lego gear onto the servo horn and axles into that. (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
The srevo parts are Nylon, hard to glue on to that. I dont think gooping on epoxy would hold vary well, might be wrong. (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
John Kittelsrud writes: > Does anyone have a solution for coupling the output of an R/C servo > to something like a Lego axel? I did it using an axle stopper glued on with hot-melt glue. Worked fine until I would over-torque it. (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | lego train and motors
|
|
Hi all. I received a cargo train for Christmas and was experimenting with the motors and speed control unit. I would like to incorporate the tracks and railway motor into some RCX projects in the near future. When I hook a regular lego motor (the (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
(...) something like a (...) The usual way the RC community does it is to use a cover from a auto tire valve stem, fill it with epoxy and push it over the splines of the output shaft. Be careful that no epoxy runs down into the bearing of shaft :-). (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | sensor details
|
|
Do the sensors read voltage or measure resistance? or both? chris (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Sensor ideas
|
|
Looking at some of the ideas for multiplexing touch sensors gave me a couple of ideas - I may not get around to constructing these anytime soon so if someone wants to run with them I'd sure like to hear how you did. Idea #1 - Whisker sensors using (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Mindstorms CD and Soft Windows
|
|
(...) It seames to be not possible to use these emulators. I've tried them all and is doesn't work. Though the software will run, the hardware won't. There are two options: use Robolab from pitsco-dacta or use Not Quite C from Dave Baum (you can (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
I use epoxy to glue on assorted pieces where I need them. If you use enough epoxy to fill the space completely, you can snap off the piece and then you have a workable Lego bump impression. What I have found with epoxy is that the epoxy holds just (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Voltage or resistance
|
|
After experimenting with various photo sensors, it appears that resistance is what is measured. Solar cells produce no change in readings, but CdS photo resisters do. I managed to hook up a BASIC STAMP (a small microcomputer by Parallax) to one of (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | The Bed Mill
|
|
I have posted some pictures of my latest mill at (URL) I will post a QuickTime movie when I complete the program and make a real cut. Bob (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Voltage or resistance
|
|
I'm joining this thread a little late, so sorry if any of this has already been stated... For "passive" sensors, the RCX measures a voltage level, but since there's a pullup you may not get what you expect. If memory serves, the RCX ADC uses a 5.0V (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|