To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 1626 (+10)
  RE: All-around-the-robot bump detection
 
Oh yeah, that too. :) Jeremy Morton a-jeremm@microsoft.com -----Original Message----- From: Fred Read [mailto:fred@corp.ne...om.net.uk] Sent: Friday, December 18, 1998 6:10 AM To: lego-robotics@crynwr.com Subject: Re: All-around-the-robot bump (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
(...) I haven't actually tried this, but I can hardly imagine that the pressure generated from just squeezing one small part of the tube is sufficient to extend a cylinder and press a touch sensor. The pressure generated will probably just "vanish" (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Hmmmmm, It's morning and I haven't had coffee yet so bear this in mind but it seems to me that this is a) a fairly cool scheme for post collision detection, and b)expandable to support direction detection through the use of 4 sensors. Imagine that (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
If you have three sections and overlap them correctly, you can distinguish six different directions of contact. You wouldn't have to multiplex the touch sensors if you didn't need any more inputs, but you could multiplex them onto one input if you (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Jeremy makes a very good point ! :) You should be able to get away with 3 (in theory). I think this "bladder" idea might work better as you could have more air displaced (assuming you hit the obstacle with any kind of speed <G> ). me Andrew Phelps (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
How 'bout this as an alternative. A flexable containment, possibly the moderate diameter rubber tube, inside which are two circuits. One is a continuous metal strip which runs along the inside edge of the outside wall of the tube. The second is a (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Why not set a variable with 1 or 0, e.g. 1=Forward, 0=Backwards. This way when the robot hits something you would know what direction it's traveling in. I haven't tried this, it's just an idea. -----Original Message----- From: Fred Read (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Conductive Foam
 
Has anyone come up with any sensors using the conductive foam used in packing IC Chips. Years ago I saw a couple books on home-brew robotics and they were using this foam as a pressure sensor. Pass a current through the foam and the resistance (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Limited number of MindStorms??
 
We'll they're over 86,000 now my RCX# is above that :) Jeff D. Payne UtahLINK Network Operations (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Limited number of MindStorms??
 
(...) What's your number? (URL) (...) Jim West NIC Architect MCI Worldcom (28 years ago, 18-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR