 | | Re: New ROBOLAB pages... (Macs to IR tower)
|
|
On 12/16/98 3:51 PM, John Donaldson, jdonaldson@ghg.net, said: (...) Ok, I haven't actually tried this, but from what I've gleaned from the messages here: 1) The Mindstorms software will NOT work under Mac emulation because of the archaic and (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Sensor information & Extreme Creatures
|
|
In article <36783E8B.7C3D@virgin.net>, Barry Bott <barry.bott@virgin.net> writes (...) Coins on the floor are no problem. What we need is a robot which finds coins down the side of the settee. (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Sensor information & Extreme Creatures
|
|
In article <F437wI.MyC@lugnet.com>, Michael Gasperi <lugnet.robotics@lugnet.com> writes (...) If you mounted a fast-response thermistor behind a lens you would have a very directional scanning heatseeker. Obviously you would need to rotate the (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: New ROBOLAB pages... (Macs to IR tower)
|
|
In article <913870749.2117423.0...ynwr.com>, Michael Westphal <westphal@intersurf.com> writes (...) In this case it isn't the IRtower which is the silly device, but the Mindstorms software. Yes, you could patch the software high or low if you could (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Funny Picture (link corrected)
|
|
Carl G. Schaefer, Jr. wrote in message <000e01be2923$6e1f6c...ic.com>... (...) It's truncated in your post again :-) so what we learn from this is not to use urls over 80 characters in email/usenet groups. Something to keep in mind when deciding in (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: RCX port information
|
|
(...) Whoa... so you mean, I can just like, take apart a 9V lead, solder them to those pins, and have 2 extra sensor inputs? or is there extra 'lectronics involved? Jasper (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: NQC software for Mac? (Robolab back ordered)
|
|
(...) Exactly! Someone would have to disassemble spirit.ocx or the Windows serial port driver to figure out how to do this. (It makes much more sense to work on spirit.ocx, because various versions of Windows will have different drivers.) Bob Stern (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: NQC software for Mac? (Robolab back ordered)
|
|
In article <367852CA.1EFBB7C2@a...up.co.uk>, Ben Laurie <ben@algroup.co.uk> writes (...) This is all getting very misleading - _not_ DCD or DTS or CD. The pairs are : RTS/CTS - normal hardware data handshaking. Careful here - I have come across 9D (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Sensor information & Extreme Creatures
|
|
In article <F437wI.MyC@lugnet.com>, Michael Gasperi <lugnet.robotics@lugnet.com> writes (...) I have used the NS LM50CIM3 for years now. This is a cheap SOT23 SMD chip and therefore nicely small too. Come in larger TO92 package too (LM50BIZ or CIZ) (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Sensor information & Extreme Creatures
|
|
(...) Yes I agree, my grandchildren thought of a robot pet and I did consider that using thermistors one could build a robopet that just looked for warm radiators to sit against, a bit like a cat or dog. Barry (28 years ago, 17-Dec-98, to lugnet.robotics)
|