 | | Re: How2 'count' in NQC
|
|
Steve, this is the third time you have helped me, and this time you obviously spent a lot of time working out the alternatives. First of all, the Wait (DELAY); in my inept code was not to flash every half second. It was to prevent additional counts (...) (25 years ago, 3-Nov-00, to lugnet.robotics)
|
| |
| | Re: Radio Controlled Tank - tread lightly.
|
|
(...) Yes, please! :) Have to check if they sell Funrise brand toys here in Sweden. //Harri Manni -"Do not take life too seriously.You will never get out alive." (25 years ago, 3-Nov-00, to lugnet.robotics)
|
| |
| | Re: MOC: Radio Controlled Tank.
|
|
(...) Here's an idea you can try to have them slip a bit less. Do you have the ordinary chain links too? Then ones without the wide tread? If so use an ordinary chain link for every third link, say. Like this: ##=##=##=##= Perhaps this will give (...) (25 years ago, 3-Nov-00, to lugnet.technic, lugnet.robotics)
|
| |
| | Re: MOC: Radio Controlled Tank.
|
|
(...) Thanks :) (...) Yes, they sure were. One of 'em I even managed to scare twice, first when the tank entered the room and then when it actually fired a projectile :) To bad it takes almost half a minute to set the cannon horisontally, I have to (...) (25 years ago, 3-Nov-00, to lugnet.technic, lugnet.robotics)
|
| |
| | Re: MOC: Radio Controlled Tank.
|
|
(...) Thanks! So do I :) (...) It's from before my dark ages, mainly the 8851 Excavator and the 8660 Arctic Rescue, I also got two with the 8843 Fork Lift truck. They usually look better then they work since they tend to slip a lot, but in this case (...) (25 years ago, 3-Nov-00, to lugnet.technic, lugnet.robotics)
|
| |
| | Re: Palm Hardware Interface idea? + other stuff
|
|
(...) It's basically the same serial data connection as the RCX. It just uses radio for transmission instead of infrared, so it goes around corners and has a longer range. Jürgen (25 years ago, 3-Nov-00, to lugnet.robotics)
|
| |
| | Re: RCX 2
|
|
(...) You can start by doing some searches on this newsgroup for the 3 or so discussions on this very topic. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 3-Nov-00, to lugnet.robotics)
|
| |
| | Re: How2 'count' in NQC
|
|
(...) The sensor returns 1 for as long as it's held down. In your code: (...) You are actually counting how long the switch is held down - in units of about a half second. So if you press and hold the switch for ten seconds, you'll get a count of (...) (25 years ago, 3-Nov-00, to lugnet.robotics)
|
| |
| | Re: RCX2
|
|
(...) Right now, it's just a different firmware package that you can download into any RCX. You can get a copy on the main Lego site and upgrade your RCX 1.0 or 1.5 to the 2.0 software level...it's a significant improvement if you use NQC - it adds (...) (25 years ago, 3-Nov-00, to lugnet.robotics)
|
| |
| | RCX 2
|
|
Hi, heh... and what is RCX2 ? Where can I find some infos about differences between RCX and RCX2 ? Thanx. Norbi (25 years ago, 3-Nov-00, to lugnet.robotics)
|
