 | | Re: Vision Command camera questions
|
|
I'm willing to bet that the issue here isn't even technical (as far as the software is concerned). It is probably the installer script which was written to check if the platform is for Win 98 or NT - and when it doesn't find either, it doesn't let (...) (25 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
| | Re: Parts - Lego or not
|
|
(...) It's not just you :-) Recently I managed a workaround to this exact situation with a 16 tooth gear by placing 1x2 tiles on the bottom plate. The gear then rests on those tiles. Of course, I fully expect to find concave crescents eroded in (...) (25 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
| | RE: Motion/Tilt Sensor from Analog Devices and the RCX
|
|
hi, just some additional information of how people use the sensor: (...) (25 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
| | RE: Motion/Tilt Sensor from Analog Devices and the RCX
|
|
Not exactly.... The output is an analog voltage, meaning it's not exactly a digital TTL 0 volts or 5 volts, but ranges from 200mv (call this low) to Vcc-200mv (call this high). But this is a PWM output, meaning that with the chip stationary with (...) (25 years ago, 16-Oct-00, to lugnet.robotics.rcx, lugnet.robotics)
|
| |
| | lego robot competition
|
|
Hi LEGO robotics fans, I am organizing the “First Internet Robot Contest”, a robotics paper contest. Submit your bot in the “LEGO robot category” and win one of the following LEGO prizes: - three LEGO Droid Developer Kits - three LEGO Vision Comand (...) (25 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
| | Re: Motion/Tilt Sensor from Analog Devices and the RCX
|
|
Sorry for my ignorance, but doesnt the datasheets mention that it contains both analog and digital outputs and either may be used. Ram (...) (25 years ago, 16-Oct-00, to lugnet.robotics.rcx, lugnet.robotics)
|
| |
| | Re: Meaning of lettering on white gearwheel.
|
|
"John Coppola" <lego-robotics@crynwr.com> wrote in message news:4.3.2.7.2.20001....net.au... (...) ft-lb as in length * force (torque or moment, not to be confused with momentum which is force*time or mass*velocity) not length/force. (...) This is (...) (25 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
| | Re: Scout SDK
|
|
Hi Mauro The link is (URL) take a look at (URL) just search hte newsgroup for vll. There's a lot of stuff out there... :o) <>s Ricardo ----- Original Message ----- From: "Mauro Vianna" <mauro_vianna@hotmail.com> To: <lego-robotics@crynwr.com> Sent: (...) (25 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
| | Re: Pneumatic actuators
|
|
8462 is best. (...) (25 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
| | RE: Motion/Tilt Sensor from Analog Devices and the RCX
|
|
From looking at the data sheets, it's going to be a bit more of a project than just "hooking it up". At a minimum you'll need to have a small micro to decode the dual PWM outputs, and they (AD) have a data sheet describing the use of a Parallax (...) (25 years ago, 16-Oct-00, to lugnet.robotics.rcx, lugnet.robotics)
|
