 | | RE: NQC versus Lego RCX Code Speed
|
|
(...) No, the Lego GUI software and NQC both produce code for the same target -- a simple interpreted virtual machine implemented in the firmware. I have never looked at the code produced by the Lego GUI, but I can't imagine it would be that much (...) (25 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
| | RE: NQC versus Lego RCX Code Speed
|
|
Wilcox, Doug (11:04 AM 10.05.2000) wrote: >Hmm. This question seems to have gone the way of my PC-->IR Tower cable >question. > >Let me try to get at the point that most interests me--what is the >difference, at the RCX level, between programs coded (...) (25 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
| | RE: NQC versus Lego RCX Code Speed
|
|
Hmm. This question seems to have gone the way of my PC-->IR Tower cable question. Let me try to get at the point that most interests me--what is the difference, at the RCX level, between programs coded in NQC and programs coded in RCX Code. Is the (...) (25 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
| | Cybermaster on sale
|
|
Yesterday I saw that the Cybermaster is on sale at the Bart Smit toy shops in the Netherlands, now only fl. 169,- (approx US$ 70) instead of fl. 449,-. I bought just one... Emile. (25 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
| | Re: Remote dead, what to do?
|
|
(...) Are you sure it is the remote? Maybe your RCX forgot its firmware, then the remote won't work. Jürgen (25 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
| | Re: A neat idea for touch sensors
|
|
(...) That probably was me ((URL) That required a lot of Lego wires, put together in funny (...) I used five wires for convenience, since I have enough of them. But you can get by with just three wires if you connect them directly to the sensors and (...) (25 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
| | Remote dead, what to do?
|
|
My remote control suddenly stopped working yesterday, and I immediately replaced the batteries, but that does not appear to have been the problem. What is the failure mode of these devices? Can the ir "bulb" burn out? If so, can it be replaced? Is (...) (25 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
| | Re: A neat idea for touch sensors
|
|
Hi Rob, (...) Yes. But by looking carefully at the connectors it's not too hard to figure out how to do it. (...) I think it is just that in most cases parallel connections are needed, and you got to decide between the two possibilities if you want (...) (25 years ago, 5-Oct-00, to lugnet.robotics)
|
| |
| | Re: Is Extreme Creatures Good? (WAS: Re: US S@H Specials, Sep 20 - Sep 26, 2000)
|
|
(...) i'll (...) Not in my opinion, just a random collection of additional parts. There is an inventory at: (URL) I didn't buy the set, so maybe owners of the set would have a contrary opinion. Kerry (25 years ago, 5-Oct-00, to lugnet.market.shopping, lugnet.robotics.rcx, lugnet.robotics, lugnet.technic)
|
| |
| | Re: A neat idea for touch sensors
|
|
(...) Those resistors in the Cybermaster touch sensors are in parallel to the sensor. You can read its value when the sensor is not pressed. Cybermaster uses it to figure out which sensor is connected to what port before starting the actual program. (...) (25 years ago, 4-Oct-00, to lugnet.robotics)
|
