 | | I have made a i2c routine for the handy board
|
|
Hello, You want to use the i2c bus (by the SPI connector) with your handy baord ? I have made a routine to use i2c component (PCF 8574, 8591.......) with the handy board. Do you want it ? See you later. Dperonne@aol.com (28 years ago, 28-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Slope in NQC
|
|
Hi Everyone, Can anyone tell me what is the NQC equivalent of the slope parameter in the Spirit.OCX SetSensorMode command. Thanks, David Strike -- Did you check the web site first?: (URL) (28 years ago, 28-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Slope in NQC
|
|
(...) Making mine Dave Baun's words: I think you can already change the slope with the existing calls. Just add the slope to the mode constant... SensorMode(IN_1, SMODE_BOOL + 10); The slope should be between 0 and 31 (inclusive). :-) Laurentino (...) (28 years ago, 28-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Working with Legos
|
|
Some of the sensors that I've used easily attach to the the plates & hlocks with holes using a set of tiny nut, bolts, and washer(s). No damage done to any of the components, and easy to change your mind about where you're going to put it. -kr (28 years ago, 28-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Working with Legos
|
|
I glued a couple of the thin Lego strips to the bottom of my HandyBoard to make it quick and easy to plop the board firmly onto a Lego base yet still have it easily removable. Doing this you must be certain to get the correct Lego spacing, so first (...) (28 years ago, 28-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Working with Legos
|
|
The LEGO purists may not approve of this, but it does work well and it makes it relatively easy to use non-LEGO components. You *do* need to be cautious about what type of glue you use. Many glues will not adhere to the LEGO plastic, others will (...) (28 years ago, 28-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Problem with VB an cybermaster
|
|
Hi Seems that I am a litle bit stupid. I am fighting with Visual Basic the first time. I want to program my Cybermaster. If I press alive I get correctly that the Cybermaster is turned on. But if I press Battery I get the errormessage "can not (...) (28 years ago, 28-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Robolab COM Ports
|
|
What about getting a switch box so you can go back and forth. Jim Clark (...) This message was sent from Bess.Net, a filtered Internet Access Provider for children and families. ---...--- -- Did you check the web site first?: (URL) (28 years ago, 28-Feb-99, to lugnet.robotics)
|
| |
 | | Re: A walking robot with (only) two legs
|
|
Andrew , (...) In its present configuration it is stable and strong enough. If you want to extend its height and weight, you have to compensate this adding more weight on the "sling", or better making it move further more "out" to the right and the (...) (28 years ago, 28-Feb-99, to lugnet.robotics)
|
| |
 | | A few notes...
|
|
Ha! Just completed my first LegOS program - and it only took a month! (off and on :) ) I'm going to note some things which stalled me, in the hope that they won't stall anyone else.. (1) I was trying to count how long the sensor was being pressed (...) (28 years ago, 28-Feb-99, to lugnet.robotics.rcx.legos)
|