To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *9611 (+10)
  Re: NQC 1.2 in beta testing
 
The thing to remember about legOS is that pretty much anything you can do in C (gcc, egcs) in 32k of RAM, you can do with legOS. I believe that both legOS and NQC have definite places in the RCX programming universe. I happen to have been using gcc (...) (28 years ago, 22-Feb-99, to lugnet.robotics.rcx.nqc)
 
  Re: lib_r2.lis ?
 
Dear Mr Pennington, Have you configured IC using ic -config command ? This sets the library file and its directory. For handy board, the library file is lib_hb.lis.This is a list file which contains the words lib_hb.c and lib_hb.icb. The lib_r22.lis (...) (28 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
 
  Re: electronics question please help
 
(...) Been there, done that! Funny. I bought almost all the same stuff from my local shack. Writting the software was the easy part ;^). (...) I've supplied some power to the inverter, yes. I'm assuming it's mandatory to have the inverter actually (...) (28 years ago, 22-Feb-99, to lugnet.robotics.handyboard)
 
  Re: HB to create video displays?
 
At 03:25 PM 2/22/99 -0500, Steve Wall wrote: [snip] In short I want to be able to watch the monitor and have (...) Checkout Decade Engineering's Bob II board at: (URL) I don't think it can do graphics, but it accepts serial input at 9600 baud and (...) (28 years ago, 23-Feb-99, to lugnet.robotics.handyboard)
 
  Re: L.E.D. question.
 
Typical drop across an LED is about 1.45v. A unit rated at 5v likely has a build in voltage drop/current limiter (read resistor). I would suggest reading the info sheet for absolute ratings. In general, 'any' generic LED will work. Buy the cheapest (...) (28 years ago, 23-Feb-99, to lugnet.robotics.handyboard)
 
  Re: electronics question please help
 
Eric - - You might try shielding the IR sensor ... add successive layers of "Scotch" tape until you get the desired sensitivity. I'm using layers of black plastic trash bags ... it blocks a lot of visible light, but very little IR. - - - Nick - - - (...) (28 years ago, 23-Feb-99, to lugnet.robotics.handyboard)
 
  using adder/subtractor as a transmission
 
I was thinking about automatic transmissions the other day and it occured to me that you could use the much talked about Adder-Subtractor setup to give you up to three speeds. Using the worm screw idea that has been mentioned, you could control the (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
 
  Sharp GP2D02 and assembly language
 
Hi, I've written a short assembly language routine to access the Sharp GP2D02 sensor and it works just great but... I have one question. Since I use the expansion board's digital outs to control the sensor I need to make sure my routine doesn't (...) (28 years ago, 23-Feb-99, to lugnet.robotics.handyboard)
 
  RE: flames
 
Thanks for allowing me on the list. I am learning many things. But why do people bicker over such trival matters as grammar or spelling. I would hope the attitude of the group would be less antagonistic but I do realize that bright people sometimes (...) (28 years ago, 23-Feb-99, to lugnet.robotics)
 
  Re : Flames
 
Well said Mac - I couldn't agree more. So come on people .....none of us is perfect .... :) I hope my spelling and gramma is correct .... :) Regards Brian -- Did you check the web site first?: (URL) (28 years ago, 23-Feb-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR