 | | datalog in legOS
|
|
I'm sure this has been discussed before, but I can't seem to find it in the archives- how can I write to the datalog in legOS? Thanks in advance. Luis ###...### "They call the faithful to their knees to hear the softly spoken magic spell:" "There's (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: LEGO UK supplementary catalogue
|
|
(...) I don't know if it's available in the US (probably is), my international catalogue is at home. The 'tank' is a cannon from the Competition sets - the plunger things gets pushed into the barrel and is fired by pulling the lever on top backwards (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | shaft encoders for a track drive
|
|
Has anybody out there constructed shaft encoders for a track driven MOBOT. If any body has I would appreciate any help you could give me. I wasn't going to use shaft encoders but I guess they are needed for many things correct? Is there anyway to (...) (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: shaft encoders for a track drive
|
|
Hi. We built encoders for a skid steered wheeled robot. There is a picture of it at: (URL) used an IR Led and reciever pair, and a white disk with 24 radial black lines, and had pretty good luck with the encoder, but bad luck with the info gathered. (...) (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Kent Farnsworth's MS-DOS port of pcode
|
|
Please help ... I've misplaced the link to download Kent Farnsworth's pcode source for use under DOS. TIA - - - Nick - - - (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: shaft encoders for a track drive
|
|
OK, now I too have my handy board, it's italian, not just the same, but has a 68hc11, and all those other thinks that make it just quite the original one similar to this. It will be interesting to see if we will can have, a day or another, a new (...) (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: Robotics sub-groups
|
|
(...) Ralph, which makes the most sense for the group name? Ending it in .h8hforth or .hforth or .forth? How narrow or wide of a scope is most suitable to the project? I gather from your source that the "h8" component is derived directly from (...) (28 years ago, 15-Feb-99, to lugnet.admin.general, lugnet.robotics)
|
| |
 | | Re: Kent Farnsworth's MS-DOS port of pcode
|
|
Thank you ... this is the link that I couldn't find. ftp://cherupakha.med...-c/ms-dos/ - - - Nick - - - (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: LEGO UK supplementary catalogue
|
|
In article <F77Dzy.11C@lugnet.com>, Dave Ryder <daver@ansuz.demon.co.uk> writes (...) Erm - as html interpreters ignore CR and LF, you can leave it in binary all the time. (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Robotics sub-groups
|
|
This is just my opinion, but I don't think that the creation of separate groups for legos or h8forth would be a good idea right now. Although a dedicated group to discuss alternative firmware is a good idea, I think overspecializing it right now (...) (28 years ago, 15-Feb-99, to lugnet.admin.general, lugnet.robotics)
|