 | | Re: A few questions...
|
|
I bought their Robot Platform (roomy and sturdy!) which came with two gearbox motors. I, too, am using the HB w/exp. If the motors you received are the same as the ones that are used on their Platform then you will have trouble using them via the HB (...) (28 years ago, 5-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: gearing problem, continued
|
|
=>From: "John A. Tamplin" <jat@Traveller.COM> =>... =>Also, what exactly is the clutch gear and is it still available? I am =>assuming it spins freely in one direction and not in the other. I recently bought an 8735 Power Pack Motor Set which (...) (28 years ago, 5-Feb-99, to lugnet.robotics)
|
| |
 | | Re: A few questions...
|
|
a few notes... in the faq there is a discussion about how to measure the resistance of a motor coil, as a way of determining if it's compatible with the hb. also in the faq, is a description of a mod that will allow using a separate power supply for (...) (28 years ago, 5-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: "Sound element"?
|
|
In a message dated 2/3/99 8:10:34 PM Eastern Standard Time, bryan.beatty@autodesk.com writes: << lego-robotics@crynwr.com >> ___...___ Yes, I've tried, but because the "sound element" is not a simple speaker, it doesn't work as espected. The top of (...) (28 years ago, 5-Feb-99, to lugnet.robotics)
|
| |
 | | Re: "synchro drive"
|
|
I'm not sure I follow the problem in the design I used. One feature which isn't spelled out on my page is that each wheel is offset from the center of its turntable by a distance equal to the wheels radius. When the turntable turns (while the (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
|
| |
 | | Re: stack pointer
|
|
Windows tips: Tip 1: Lose Windows!!! Reboot your computer, hit "F8" when the little message "Starting Windows 95" comes up. Select the option "Command prompt only". Now, run IC and/or DL and you should have no problems. Basically, windows is nothing (...) (28 years ago, 5-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Botcode/SetWatch
|
|
HI: I have a few questions. Is there a way to use a variable in the SetWatch command? When Programing with BotCode. for example: (this does not work) ---...---code---...--- int x int y set x 10 set y 10 BeginTask 2 setwatch x y EndTask (...) (28 years ago, 5-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Alternate C compiler for LegOS
|
|
(...) Dave Madden posted a pointer to his prebuilt binaries: ftp://ftp.webvision....-tools.ZIP Alternatively, have a look at (URL) I've done a similar but lazier job of just providing an add-on lump to Cygwin (ie, you need Cygwin first). I have to (...) (28 years ago, 5-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Matrices with Interactive C?
|
|
I don't think it 'directly' supports matrices, but I have used a 2 dimenstional array to simulate a matrix. You may have to write some functions for multiplication etc, but it works ok. -----Original Message----- From: Peter Eacmen (...) (28 years ago, 5-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: gearing problem, continued
|
|
(...) Yes Ncm is a unit of torque, Newton-centimeters. However, I have no idea quantitatively how much torque that is since I haven't ever measured the output of the Lego motors. Have you ever had it slip when the drivetrain wasn't stalled? John A. (...) (28 years ago, 5-Feb-99, to lugnet.robotics)
|