To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8796 (+10)
  Re: Re: R4 Resistor
 
"Fred G. Martin" schrieb: (...) i have had the same problem, so i havent installed the ir-circuit yet. the mistake is in "The Handy Board Technical Reference" (July 12, 1998) PDF File ... On page 46 ( i am not sure) is a Part Listing: it says : .... (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
 
  Fw: 360 deg. swiveling electrical connection
 
Are you looking for a Lego pure solution? I have a though about some rotating metal disks that touch each other and are always in contact no matter what the rotation, but am not an EE, so I don't know if polarity would become an issue. trowt (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: R4 Resistor
 
thank you! yes, 3.83k is correct. fred In your message you said: (...) ile (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
 
  Re: Memory erase or reset?
 
Either disconnect the batteries and all sources of power or remove the memory chip.... -phil (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
 
  Re: NVRAM
 
Dallas Semiconductor makes some static RAMs with an internal battery. One of them is the DA1230AB/Y, a 256kbit (32Kbyte) battery backed static RAM. (URL) - - - Nick - - - (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
 
  Re: What is your current Mindstorm project?
 
(...) [ ... ] (...) This is exactly what I'm working on (as a long term goal). I only got my mindstorm a few days ago so I haven't gotten far. Currently I'm just trying to get my robot to survive in my flat for more than a minute! ;-) The main (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Unsubscribe
 
Thank's for the help !! Bye (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
 
  Re: Adder/Subtractor revisited
 
Well, I don't know about your experiences, but I have had tracked vehicles with identical (as much as possible) construction on each side of the vehicle that deviat several degrees for each foot travelled. This was due to the characteristics of the (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: 360 deg. swiveling electrical connection
 
Ben Kimball wrote in message ... (...) What about an axle with wires running along two of the groves (groves made by the cross section of the axle). You could have a two bands of thin metal sheeting wrapped around the axle. To each band you have on (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
 
  Re: Fw: 360 deg. swiveling electrical connection
 
I am an engineer with EE training. It would not be a problem if you use two concentric rings. One for the "live" voltage and one for a ground (or positive and negative if you prefer that notation). This is how many real world systems work. Matt R. (...) (28 years ago, 4-Feb-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR