 | | Light outputs on RCX
|
|
Has anyone ran lights from the RCX outputs? I need something brighter than an LED, any ideas? Thanks, Bryan Bible --- __o --- __o Tandem Computers --- _ \<,_ --- _ \<,_ Austin Texas --- (*) / (*) --- (*) / (*) bryan.bible@compaq.com -- Did you check (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
(...) I took apart a laser pointer. I put the laser module into a mutilated brick. I added a diode, an LM-317, appropriate resistors and a .1uF capacitor to make a 3 volt power supply. The diode makes it so the laser is on for motor forward, off for (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
Paul Haas writes: > On Mon, 18 Jan 1999, Bible, Bryan wrote: > > > Has anyone ran lights from the RCX outputs? I need something brighter than > > an LED, any ideas? > > I took apart a laser pointer. I put the laser module into a mutilated > brick. I (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: digital and analog port on HD
|
|
(...) A digital port can't have the capability of an analog port, since it has only one bit of information with which to work. (A 256-value analog port has eight bits.) You could perhaps hook an analog sensor up to a digital port using some sort of (...) (28 years ago, 18-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: digital and analog port on HD
|
|
(...) Just thought I would add that it *is* possible (if a bit slow) to read an analog signal w/ a digital port by timing the decay of the signal thru a RC circuit...not a particularly precise method, either. < Watching for the Fedex guy bringing my (...) (28 years ago, 18-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Where is "R4" on Handy Board Extension Schematic?
|
|
I have just finished building the extension board, and, while it appears to work all right, I can't seem to find resistor R4 on the schematic. The power transistor near the on/off switch is getting quite hot with the expansion board piggybacked on (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Douglas Electronics Expansion Board.
|
|
I ordered the kit the first day I could. I got it last Friday, and put it together over the weekend. The douglas board comes with NO assembly instrictions! These are some notes that ought to make things easier for others: RP1 & RP2: The both have a (...) (28 years ago, 18-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: new Throwbots
|
|
(...) I doubt that these joints will be of much use - they're way to rigid, and there is not a real good place to attach a motive link. (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
(...) I made several diffrent color (even flashing!) lights with the mini xmas lights. they are real bright if you set the output to 8 or they work at any level. I took the bulb out of the little plastic holder and soldered wires to the wires on the (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: new Throwbots
|
|
(...) I just bought 2 of the new throwbots, Granite and Electro. I am not very impressed. The best part about them is the colored gears. Only because I am tired of gray. ---...--- @¿@ (URL) ,-, Follow the adventures of Capt. Jack Napalm! One thing (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|