 | | Re: Self learning robot with neural brain
|
|
You can get the control creation edition of VB5 for free. It will allow you to write software, you just can't compile a stand alone executable. It seems to work just fine with spirit.ocx. I can't remember the exact link, but you should be able to (...) (28 years ago, 10-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Self learning robot with neural brain
|
|
I don't have to worry about the size (I have a cable modem :) ), I just need to know if I can still run the neural net program without a compiler. -Chris Joel Kunze wrote in message ... (...) seems (...) you (...) (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Self learning robot with neural brain
|
|
I don't see any reason why it would not work. It is just that you have to have the visual basic environment running at the same time, sometimes a little clumsy, but still functional. I use the control creation edition for various things like (...) (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | HB and Acceleration
|
|
Hello, Does anyone here know how acceleration will affect the operaion of a handyboard, and also will sudden changes in altitude (like, 3,000 feet in less than ten seconds) affect it's operation? I have a High Power Rocketry launch coming up in May, (...) (28 years ago, 11-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: HB and Acceleration
|
|
(...) I presume that you are not planning on using my infrared control software! Good luck in your project, it sounds like fun. Wanna tell us more about it? /Max (28 years ago, 11-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Book on Robot Sensors and Navigation Techniques.
|
|
Thanks to Carl Schaefer for posting the URL for the Robotics Reference entitled: Where am I? Sensors and Methods for Mobile Robot Positioning by J. Borenstein , H. R. Everett , and L. Feng I have looked into the Table of Contents and have begun (...) (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | Cut Price Mindstorms in the UK...
|
|
I hate - and I do mean *HATE*, paying full price for anything and would like to get a couple of Mindstorms kits for educational purposes (OK, OK, I'm going to play with them) but everywhere I look [here in the UK] has them at the full RRP of (...) (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | Wireless Handyboard Link ?
|
|
Hello, I am investigating createing a wireless serial link between my PC and handyboard. The cheapest solution I've found is the RF module from Lynxmotion. Does anyone have any experience with this, or perhaps suggestions for simpler or more (...) (28 years ago, 11-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | More small changes to firmdl.c
|
|
Two more small changes to firmdl.c. Gavin Smyth reported seeing long delays while downloading firmware, and suggested a fix that may or may not have much effect, depending on your system. That fix, which limits the number of response bytes waited (...) (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
(...) I'd take a couple if they were in the $15 dollar range. -Blake -- Did you check the web site first?: (URL) (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | Expansion board motor outs???
|
|
I just wanted to verify something before I went and purchased the expansion board. Are the HB's motor outputs still available when using the expansion board. It is unclear in the doc. Thanks, Aaron (28 years ago, 11-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Fw: RcxCC Joystick controls
|
|
Very simple. Write a little nc program that defines some tasks. Download it to the robot but don't run it. Here is a trivial example. After downloading it, the first button will start motor B and the second button will stop it. (Note that the order (...) (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Pneumatic Tanks
|
|
(...) :-) (...) Syringes? That's injection needles, right? Hm. Now where do I get disposable syringes? Ah, I figure I'll find something I can use somewhere. Thanks for the idea! Fredrik (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | Re: ideas?
|
|
This should have worked - are you sure that you replaced your old Menus folder with the one in the extras folder? see ya (...) Associate Professor Department of Mechanical Engineering Tufts University Medford, MA 02155 email: crogers@tufts.edu (...) (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | motor ports
|
|
Hi all, Is it possible to add more motor ports to the handy board by simply copying the existing motor drive circuit and putting them on the expansion header where the extra chip select lines are. if so what changes would be needed to make IC (...) (28 years ago, 11-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Book on Robot Sensors and Navigation Techniques.
|
|
As long as we're on the subject of books, I'd like to recommend "Mobile Robots" by Anita Flynn and Joe Lee Jones: (URL) a fascinating book, full of hands-on information. It contains step by step instructions for building several robots, including (...) (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | Motor Ports
|
|
Hi all, Is it possible to add more motor ports to the handy board by simply copying the existing motor drive circuit and putting them on the expansion header where the extra chip select lines are. if so what changes would be needed to make IC (...) (28 years ago, 11-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | DL problems
|
|
I put together the HB shortly after it first became available. This is key because it worked-downloading and all. I put it down for a year because of family problems but all that time left it plugged in because of the Ni-cad. I feel that should (...) (28 years ago, 11-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Pneumatic Tanks
|
|
Fredrik Glöckner wrote in message ... (...) Yes, injection needles. Make sure to get a small gauge needle. Since the air is thin, you need a small restriction to see any reduction in flow. Drug stores normally have disposable needles, but you might (...) (28 years ago, 11-Jan-99, to lugnet.robotics)
|
| |
 | | Re: The Ten Commandments of Lego
|
|
What happened to Thou shalt not glue Lego? (...) -- Technical Support requests should be sent to support@opendisc.com Joe Greene Technical Support OpenDisc Systems, Inc. Boulder, Colorado, 80301-2442 USA 303-546-0460 Joe_Greene@OpenDisc.Com (28 years ago, 11-Jan-99, to lugnet.robotics)
|