To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *7531 (+10)
  Re: 3 sensors = 8 inputs?!
 
(...) Unless you add a bit of electronics to multiplex your sensors, use the existing three digital inputs as a mini parallel port, design a simple communications protocol and send the sensor statuses from the module to the RCX using the protocol. A (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  supplier for Sharp IS1U60 infrared demodulator
 
Hello Folks- A couple of months ago I built a HB with the exception of one part... U15 (Sharp IS1U60 infrared demodulator) ... I now have the need. I am looking for the info for a supplier or individual that will sell a small number(2). I'm in the (...) (28 years ago, 7-Jan-99, to lugnet.robotics.handyboard)
 
  Re: 3 sensors = 8 inputs?!
 
(...) The way the inputs work does not allow hooking something up to two inputs at the same time while still keeping independent use of the inputs. You would need to add at least diodes. I assume you want a pure LEGO solution, but LEGO doesn't have (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  2 Motors off one output???
 
I'm sure that this has been covered before, but!!! Has anyone (or can it be done) hooked two motors(i want them to move in the same direction) up to one of the "A", "B", or "C" outputs. Clay Aucoin Director of Information Technologies, Web Services (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: CM in LDraw
 
(...) Answering my own post: I was told L3P ((URL) can make the edges disappear when rendered with POV-Ray ((URL) trick is to put the DAT file into the PARTS directory. Laurentino Martins *<||:-) [mailto:lau@mail.telepac.pt] [(URL) you check the web (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Help With Programming
 
I am looking for help in programming the RCX using Visual Basic 5.0. I can issue immediate commands successfully, ie turn a motor on or off, however I can not get programs to download into memory. Programs will download successfully into memory (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  legOS help needed
 
I have downloaded cygwin32 and the binaries that were precompiled. I have also compiled Markus's sample programs and the firmdl.c file distributed with legOS. However, when I try to run firmdl, it says that it can't find the srec file (e.g. firmdl (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: Pneumatic Tanks
 
Well, you can break those bottles... In high school, we made squirt guns out of plastic 2 litre pop (soda) bottles and about $20 worth of pipe fittings from the local hardware store. These thing were quite the beasts, compared to the little hand (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: RcxCC Joystick controls
 
(...) This will be in the next release (together with arrow buttons that you can push with the mouse). Mark Overmars (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: So why build robots out of LEGO in the first place?
 
Dear David my sinful son, The first step on the path to redemption to for you to tithe ten percent of your LEGOs to *me* every month! - - - Nick - - - (...) (28 years ago, 7-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR