To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6856 (-20)
  Re: Voltage or resistance
 
I'm joining this thread a little late, so sorry if any of this has already been stated... For "passive" sensors, the RCX measures a voltage level, but since there's a pullup you may not get what you expect. If memory serves, the RCX ADC uses a 5.0V (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  The Bed Mill
 
I have posted some pictures of my latest mill at (URL) I will post a QuickTime movie when I complete the program and make a real cut. Bob (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  DC Motor Manufacturers
 
Hello everyone, Has anyone found a good source for DC motors? I am looking for small motors to use as direct drive movement of a small 1.5 LB robot. Any help is greatly appreciated! Bill Denzel Senior Mechatronics Student California Polytechnic (...) (28 years ago, 27-Dec-98, to lugnet.robotics.handyboard)
 
  Voltage or resistance
 
After experimenting with various photo sensors, it appears that resistance is what is measured. Solar cells produce no change in readings, but CdS photo resisters do. I managed to hook up a BASIC STAMP (a small microcomputer by Parallax) to one of (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
I use epoxy to glue on assorted pieces where I need them. If you use enough epoxy to fill the space completely, you can snap off the piece and then you have a workable Lego bump impression. What I have found with epoxy is that the epoxy holds just (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: Mindstorms CD and Soft Windows
 
(...) It seames to be not possible to use these emulators. I've tried them all and is doesn't work. Though the software will run, the hardware won't. There are two options: use Robolab from pitsco-dacta or use Not Quite C from Dave Baum (you can (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Sensor ideas
 
Looking at some of the ideas for multiplexing touch sensors gave me a couple of ideas - I may not get around to constructing these anytime soon so if someone wants to run with them I'd sure like to hear how you did. Idea #1 - Whisker sensors using (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
 
  sensor details
 
Do the sensors read voltage or measure resistance? or both? chris (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
(...) something like a (...) The usual way the RC community does it is to use a cover from a auto tire valve stem, fill it with epoxy and push it over the splines of the output shaft. Be careful that no epoxy runs down into the bearing of shaft :-). (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: Downloading problems
 
I haad similar problems and then I realized that I did not need to download pcode or anything special. I just ran IC and it connected -- all the ports are working fine... Scott Sherman (...) (28 years ago, 27-Dec-98, to lugnet.robotics.handyboard)
 
  lego train and motors
 
Hi all. I received a cargo train for Christmas and was experimenting with the motors and speed control unit. I would like to incorporate the tracks and railway motor into some RCX projects in the near future. When I hook a regular lego motor (the (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
John Kittelsrud writes: > Does anyone have a solution for coupling the output of an R/C servo > to something like a Lego axel? I did it using an axle stopper glued on with hot-melt glue. Worked fine until I would over-torque it. (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
The srevo parts are Nylon, hard to glue on to that. I dont think gooping on epoxy would hold vary well, might be wrong. (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
You could glue a lego gear onto the servo horn and axles into that. (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  R/C Servo to Legos
 
Does anyone have a solution for coupling the output of an R/C servo to something like a Lego axel? Thanks. (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  RCX Serial
 
I'm embarassed to post with such a trivial discovery, but in the hopes of saving somebody a little time: You can get the serial port to transmit under legOS by doing *((char *)0xffd0) = 0x09; // TCR *((char *)0xffd1) = 0x13; // TCSR *((char (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: Downloading problems
 
(...) please download the latest 6811 Downloader for Macintosh, just posted last week on the HB web site. Fixes compatibility probs. (...) th the (...) OK, yes, you've already downloaed. (...) plus (...) please download these files from the HB web (...) (28 years ago, 27-Dec-98, to lugnet.robotics.handyboard)
 
  Re: sensor connectors
 
OOoopsss... LegoMajik@aol.com not LegoCork, that's Mindstorms name. Dohh!!! (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: sensor connectors
 
2 pins are power and 2 are ground. It's made that way so the connector can go in several ways. You can reverse motor direction just by turning the power connector at either end. LegoCork@aol.com (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: Non-standard differential wanted
 
Just wanted to let everyone know that I updated my webpage with this design. The page is (URL) It now contains pictures of a robot using the address/subtractor that my father built. His layout of the adder/ subtractor is more efficient (direct drive (...) (28 years ago, 26-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR