To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6651 (-10)
  Re: 3-wheel drive site wanted
 
Kerry Garrison wrote in message <000001be2bd9$7b23e4...@mordo>... (...) Here it is one. From here there are links to the others. (URL) (28 years ago, 20-Dec-98, to lugnet.robotics)
 
  Re: 3-wheel drive site wanted
 
Sorry, I can't remember the URL, though I had a look there myself when it was mentioned before. What I find fascinating is how we all seem to agree on what are interesting problems, yet come up with solutions so radically different in detail. On my (...) (28 years ago, 20-Dec-98, to lugnet.robotics)
 
  3-wheel drive site wanted
 
The other day I found a site that showed the creation of a drive train using 3 wheels per axle as in the vehicle used on Damnation Alley. I cannot find the URL, any help would be appreciated. -Kerry (28 years ago, 20-Dec-98, to lugnet.robotics)
 
  List digest mode available?
 
Hi, I'm a new subscriber to this list, impressed, if not slighltly overwhelmed by the volume. Does the list server provide a "digest" mode? (My ancient mail reader doesn't have any filtering capabilities...) And, thank for all the Mindstorms info. I (...) (28 years ago, 20-Dec-98, to lugnet.robotics)
 
  Re: legocad
 
Hello All, Has anyone out in the ether used the lego-cad program? If you have, is it possible to hack into it? I would love to add parts from the mindstorms kit (28 years ago, 20-Dec-98, to lugnet.robotics)
 
  Re: stepper motors from 5 1/4 drives
 
Hi! (...) okay, another newbie reply :-) After I received this message I opened several 5 1/4 drives that were going to trash at my job and took all the stepper motors and integrated circuits. Here's what I figured out: 1 - All the stepper motors I (...) (28 years ago, 20-Dec-98, to lugnet.robotics.handyboard)
 
  Re: Vertical Mill
 
Robert Fay writes: > I have posted pictures and a QuickTime movie of my new vertical mill at > (URL) adding all of these to the ``Building'' section of the list web site at (URL) It would be great to know if the model is ``Mindstorms-Pure''. I'm (...) (28 years ago, 20-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
to Dennis Parker's point OK so you get this tube wired up to act as a switch. What's the energy drain on your batteries? What are the voltages required to exceed the limit value of the actuator? It sounds more accurate than an air filled tube (...) (28 years ago, 20-Dec-98, to lugnet.robotics)
 
  Re: a/d range
 
Hi friends! Thank you for the replies about this topic. Now I could get a Reference Manual too... The a/d range is determined by the references given to the VrefH and VrefL pins. But be careful about this: "There should be at least 2.5V between (...) (28 years ago, 20-Dec-98, to lugnet.robotics.handyboard)
 
  New robotics website online
 
Check out www.robotbuilders.com Add a link to your website in the Web Links section. Regards, Mark Williamson (28 years ago, 19-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR