 | | Re: Limited number of MindStorms??
|
|
We'll they're over 86,000 now my RCX# is above that :) Jeff D. Payne UtahLINK Network Operations (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Conductive Foam
|
|
Has anyone come up with any sensors using the conductive foam used in packing IC Chips. Years ago I saw a couple books on home-brew robotics and they were using this foam as a pressure sensor. Pass a current through the foam and the resistance (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
Why not set a variable with 1 or 0, e.g. 1=Forward, 0=Backwards. This way when the robot hits something you would know what direction it's traveling in. I haven't tried this, it's just an idea. -----Original Message----- From: Fred Read (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: All-around-the-robot bump detection
|
|
How 'bout this as an alternative. A flexable containment, possibly the moderate diameter rubber tube, inside which are two circuits. One is a continuous metal strip which runs along the inside edge of the outside wall of the tube. The second is a (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
Jeremy makes a very good point ! :) You should be able to get away with 3 (in theory). I think this "bladder" idea might work better as you could have more air displaced (assuming you hit the obstacle with any kind of speed <G> ). me Andrew Phelps (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
If you have three sections and overlap them correctly, you can distinguish six different directions of contact. You wouldn't have to multiplex the touch sensors if you didn't need any more inputs, but you could multiplex them onto one input if you (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
Hmmmmm, It's morning and I haven't had coffee yet so bear this in mind but it seems to me that this is a) a fairly cool scheme for post collision detection, and b)expandable to support direction detection through the use of 4 sensors. Imagine that (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: All-around-the-robot bump detection
|
|
(...) I haven't actually tried this, but I can hardly imagine that the pressure generated from just squeezing one small part of the tube is sufficient to extend a cylinder and press a touch sensor. The pressure generated will probably just "vanish" (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
Oh yeah, that too. :) Jeremy Morton a-jeremm@microsoft.com -----Original Message----- From: Fred Read [mailto:fred@corp.ne...om.net.uk] Sent: Friday, December 18, 1998 6:10 AM To: lego-robotics@crynwr.com Subject: Re: All-around-the-robot bump (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
The tubing is such a small diameter that I think it would take a large surface of contact for enough air to be displaced to move a pneumatic cylinder. Maybe with not-Lego(tm) tubing that was, maybe 1/4 to 1/2 inch [6.35 to 12.7 mm :P ] in radius (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|