To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6541 (-10)
  Re: NQC software for Mac? (Robolab back ordered)
 
(...) DTR/CD aren't alternatives, they serve an entirely different purpose. The PC software toggles the CTS signal, which the tower shorts to RTS, so that it can tell if the tower is connected. Since the Mac serial port doesn't have those pins, (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
 
  Warning: No CyberMaster in Macs
 
I've been reading some posts regarding Mac problems and I noticed that no one ever referred to CyberMaster problems in Mac (which is a good thing). Unfortunately people with Macs are _destined_ to not be able to use their CyberMaster, since it's not (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
 
  Batteries?
 
Hello All, Is there a rechargable batteries that anyone can suggest to use with the RCX? How long does a group of batteries usually last? What happens to the programs stored in the RCX when the batteries rundown? (28 years ago, 16-Dec-98, to lugnet.robotics)
 
  RE: NQC software for Mac? (Robolab back ordered)
 
It's been a long time since I worked with serial hardware, but isn't there an alternative pair of pins to RTS/CTS? DTR/DTS or something like that? If the Mac sets the other pins you might be able to short them to the RTS/CTS pins. I know I've done (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
 
  Re: NQC software for Mac? (Robolab back ordered)
 
(...) It will *never* work. The PC software fiddles with the RTS and CTS pins, which the Mac *does not have*. --- Chris Osborn FozzTexx Enterprises 707 226 7629 - Voice 2136 Coronado Ave. 707 253 3063 - Fax Napa, CA 94559 <fozztexx@fozztexx.com> (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
 
  !! Off Topic !!
 
A little over one hour ago the tail started to wag the dog (again)! - - - Nick - - - (28 years ago, 16-Dec-98, to lugnet.robotics)
 
  Re: unsuscribe
 
I don't know if you guys are serious or just mocking the first attempt at unsubscribing, but if you send an blank email to the address indicated you will be unsubscribed from the list. lego-robotics-unsubs...crynwr.com instructions were found in the (...) (28 years ago, 16-Dec-98, to lugnet.robotics)
 
  Archives?
 
I just joined this list. Is there somewhere or some way to look at archives from the list? Thanks, Bill Ramsey (28 years ago, 16-Dec-98, to lugnet.robotics)
 
  unsuscribe
 
unsuscribe (28 years ago, 16-Dec-98, to lugnet.robotics)
 
  NQC software for Mac? (Robolab back ordered)
 
hi bob I'm also wrestling with the Mac problem. I'm looking for someone who tried getting it working with Virtual PC 2.0. The software runs perfectly, but i've got some trouble to communicate with the IR unit. I'm using a ordinary modem-cable to (...) (28 years ago, 16-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR