To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6201 (+20)
  Re: Do It Yourself RF module????
 
Bastiaan: I wanted to suggest that you investigate the Ham Radio community. Some search words to help get you started include PACKET and ARRL. The first is one of the digital communications protocalls used in Ham Radio, and the second is an (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  Re: effect of motor speeds
 
(...) I think so, most problematical is the reduction in starting torque, free running always seems to peak at the same RPM. With an Acrobot based robot I have problems with wrinkles in the carpet stopping it when manoevering at low speed, but it (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: effect of motor speeds
 
(...) I think it depends a lot on the weight of the robot and the type of mobility used. For instants, when I use tracks on my CyberMaster, 1 is very very slow and 7 is fast. All the other numbers between have speeds more or less according to this (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Stepper vs DC
 
(...) Actually, steppers do have some advantages. 1) If you do not have encoders on DC gearhead motors (or wheels, etc) they are notoriously hard to position accurately. Steppers can be controlled very accurately. Most servo motors cannot rotate (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  stepper motors from 5 1/4 drives
 
Okay, another newbie question: What do I need to take out of the 5 1/4 drive, other than the motor to get this to work? Also, what about drivers for the same? Anyplace I can get more info on this? I have a bunch of old drives laying around. thanks (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  Re: effect of motor speeds
 
Humm... I think I switched the legends. Laurentino Martins (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Communicating with IR tower
 
(...) Have you already done this? (detect out of range situations?) I'd really would like to know how did you do it! I also have a CyberMaster and I'm working with NQCC and with the Spirit.OCX in VC++. Thanks! Laurentino Martins (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Where to buy in London
 
In article <VA.000017c1.05e516c...pthought>, John Cooper <robots@jpsc.co.uk> writes (...) ... and the shop at Legoland Windsor is open until sometime before Christmas. I got mine (well my sons!) the for a 10% discount off UKP160 as he was a lego (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Out of range
 
[transferred to a new thread] I'm trying to create a good algorithm for detecting out of range situations with the tower, using NQCC. Have anybody already found a good way of doing this? My guess is that this is not possible, but... I have a (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Wall Street Journal on Lego Mindstorms
 
The Wall Street Journal has a nice (albeit technologically simplified) article today on Lego Mindstorms' popularity among adults. It's not, to my knowledge available on-line, and for copyright reasons I won't post it all here. But here's a couple (...) (28 years ago, 10-Dec-98, to lugnet.announce, lugnet.general, lugnet.robotics)
 
  Re: Stepper vs DC
 
It depends. if you are looking for higher top speed and more torque using less power, DC may be the way to go. If you want accuracy but don't want to deal with shaft encoders and the code overhead needed to precisely control and monitor your DC (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  How to get digital outputs from the handyboard???...???
 
hi everyone, i have been trying for the past few days to get digital outputs from the board but with no success. i have been trying to get digitals outputs from the SPI's pins (J6). i have poke to make the port as output port. but the problem now is (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  Re: Out of range
 
Hi, I have some code that does this but it get kind of complicated to explain but here goes.... 1. I have a separate thread in my (C++) app that is used to poll the cybermaster variables. I can set which variables to check under program control. 2. (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  How to get digital outputs from the handyboard???...???
 
hi everyone, i have been trying for the past few days to get digital outputs from the board but with no success. i have been trying to get digitals outputs from the SPI's pins (J6). i have poke to make the port as output port. but the problem now is (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  Servos for the miniboard
 
I would like to use a servo to operate the throttle of a small gas engine. I am planning on using the miniboard to control the servo. Are there any brands to avoid? Are there any brands that are far better than the rest? Will just about any RC servo (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)
 
  Re: 2 RCX communication on the same model
 
(...) You mean the RIS/GUI language? It _does_ have an IR message function. (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Pre-LEG British bricks
 
What again was the name of the British bricks back when LEGO started? What again was the webpage with pictures of them? Eric Brok (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Wall Street Journal on Lego Mindstorms
 
(URL) has this article for subscribers. I found it by searching for Mindstorms. It doesn't give back a URL useful for anyone else, but others can probably the article by doing the same search. alex (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Pre-LEGO British bricks
 
Eric Brok wrote in message ... (...) To answer my own questions: Kiddicraft (URL) Brok (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  How to get digital outputs from the handyboard???...???
 
hi everyone, i have been trying for the past few days to get digital outputs from the board but with no success. i have been trying to get digitals outputs from the SPI's pins (J6). i have poke to make the port as output port. but the problem now is (...) (28 years ago, 10-Dec-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR