 | | Compling *.ICB files
|
|
Hello, Does anyone have any tips on compling *.ICB files on Windows NT? I have IC 3.2. Using the as11_ic.bat file works with much modifications to the the *.asm files. The web based complier at Newton Labs compiles the code, but loading the ICB file (...) (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: gear differential [URL]
|
|
Hello, all... I was the one that brought up using a gear differential to solve another's problem. Here is a URL of a better design than mine. (URL) you. PS: new project Got the idea looking at the design for a Lego Joystick... Robotic Fencing! 3 (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | Re: gear differential [URL]
|
|
(...) experience with this is kinda bad. I once did something quite similar, but when the drivetrain was loaded, one of the motors reversed, making the diff output zero. This happened, BTW, when I geared down the motors by 3:1 before passing the (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Building gcc
|
|
YES, now i added the bin directory with the sh in it ! Configure now works fine, but make complains about some bfd.h missing (and no rule to make it) in bfd Directory ! There is a bfd-in.h and a bfd-in2.h but no bfd.h. I tried configuring the whole (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | serial communication
|
|
Hi, Does anyone know the what is the most suitable port settings to use ? The Bits per second, number of data bits and stop bits, parity bit and the flow control type. Thanks for helping... (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Building gcc
|
|
Hello, Some time ago I tried to compile binutils 2.9.1 for H8/300 with cygwin on NT and I was also getting compilation errors. People from the binutils development team (Ian Lance Taylor, ian@cygnus.com and Kai Ruottu, karuottu@freenet.hut.fi) (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | Re: One tip, and a few questions.
|
|
(...) 0-100. 100 being very very bright. (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Sharp IS1U60 availablity
|
|
Check B. G. Micro 800-276-2206 www.bgmicro.com I would not be too concerned with the actual part number, just look for an Infared sensor or remote control sensor. Also get the pin outs as these may be different. Also have you considered using fewer (...) (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: motor port problem .
|
|
Philip In a message dated 98-11-19 21:05:04 EST, you write: << hi, I have a big problem. I followed the method of yours that just lift up pin 8 of one L293 and wirewrapped it. The positive supply is wirewrapped to pin 8 . How about the negative (...) (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | TEST
|
|
TEST (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | TEST
|
|
TEST (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | BrickCommand
|
|
Seems like everyone is writing software for the RCX these days. Well, I've written one for myself and figured I would put it on my website if anyone is interested. Check out: (URL) and go to the Lego section. It's a program editor/tester/debugger (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | RE: BrickCommand
|
|
For some reason, the webpage loads slowly. Maybe Geocities or maybe my fault in bad webpage design, I don't know. If anyone knows why, let me know! Thanks again! (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | Dark Grey Idler Gears (was Re: gear differential)
|
|
(...) teeth, (...) mechanically (...) FYI - the Technic Future Car (not to be confused with the Super Car) has three of the aforementioned idler gears, along with some other nice pieces, for about $44. Recommended. Regards, Issac. Knoxville, Tn (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | RE: gear differential
|
|
(...) this is a fantastic device. i played with it today and build a new robot platform using it. i also flattened it by one layer, and i also make it one element wider (to make its width an even number, which makes it easier to work with). the main (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | Re: gear differential
|
|
I'm looking forward to seeing your improved design. Ken ---...--- (...) device (...) flatten (...) motors (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | RE: gear differential
|
|
On Fri, 20 Nov 1998, alex wetmore wrote: <snip> (...) Yes, there is some loss with all of those gears, but I think that it is a small price to pay for not having to worry about the vehicle veering off course because of a mismatch in motor speed due (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | BrickCommand update
|
|
To those of you who downloaded BCFull.zip and received an error -- SORRY!!! I missed a file or two in the setup and have now fixed it and put the new one on the website at: (URL) you didn't get any errors, that means that your system already has the (...) (28 years ago, 20-Nov-98, to lugnet.robotics)
|
| |
 | | Re: LEGO: looking for gears
|
|
(...) Call 1-800-453-4652 for a Lego Shop-At-Home catalog. They have an assortment called #5229 Gears & Differentials for $4.50, that has all but the huge 40-tooth gears. Shipping is free. If you need the 40-tooth gears, you can get four of them (...) (28 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | pictures of gear differential
|
|
I smacked together a page on my gear differential using standard gears and pieces. Find it at the URL below. (URL) (28 years ago, 20-Nov-98, to lugnet.robotics)
|