 | | RE: moving in a straight line with two motors?
|
|
G'Day My 3 cents (Canadian, Eh). The most elegant solution I have seen to this problem I believe came from an old Milton Bradly 'Big Trak', in which the designers used a magnetic clutch. The idea is simple , getting the forces involved to balance (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
Ah-Oh... Magnets in close proximity to the RCX brick may not be a wise idea. On just about all of my mobile bots, the motors are immediately adjacent to the RCX brick. Just my 2 cents (US, of course!) Carl -----Original Message----- From: Giesen, (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
Giesen, Oliver writes: > Basically you get two large pulleys (or bars) and mount two magnets opposite > each other on the same side, one pulley has the two north poles facing out > and one has the two south poles facing out, when the two pulleys are (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
I might be able to use this solution for another problem. My wheeled bots have a strong tendency to go in whichever direction is necessary to run into sleeping cats. Straight line, pull to right, pull to left -- as long as there's a sleeping cat in (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
Carl G. Schaefer, Jr. writes: > Ah-Oh... > > Magnets in close proximity to the RCX brick may not be a wise idea. On just > about all of my mobile bots, the motors are immediately adjacent to the RCX > brick. The RCX has no magnetism-sensitive parts, (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) <snip> (...) Hey, sounds like goal right up there with the Mindstorms commercials - shoving all the plates off the dinner table, snapping pictures of women in the shower, etc. Great to see the big problems being solved on this list....:-> (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) So _that's_ what they mean by a "pussy magnet"! (Sorry, sorry, I just couldn't resist). Cheers, Ben. (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
Uhh --- that was a stupid comment, wasn't it? How do the Lego guys guard (or shield) against the possibility of the motor magnets disrupting the electronics or memory onboard the RCX? Carl (with a very red, I-can't -believe-I'm-an-engineer, face) (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Tim, Instead of using the differential for angle sensors, why not use it to allow a single motor to drive both wheels? Then a single angle sensor coupled with a motor could drive the steering mechanism. This setup would be very similar to a radio (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) At one point, in the distant past, I saw plans for a gear box that used either 2 or 3 differentials, I do not remember which. 2 motors were used, 1 to drive both axles, one for steering. axle1 == motor1 + motor2 axle2 == motor1 - motor2 With (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|