To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5146 (+10)
  Re: MindStorms at Robot Store (Hacking Lego Compatible Parts)
 
I have some black ones as well, I think its for colour coding - yellow for sensors, black for third motor. I think I prefer the old grey cable as its more flexible. Perhaps the stiff thin black cable is supposed to last longer. On the Cybermaster (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: RCX Programming Questions and Sensor Ideas
 
(...) Does that support an arbitrary number of tasks? If there are n tasks numbered 1 to n, and task k delays for k cycles on failure, I think you still have to be careful to make sure that the number of tasks n is smaller than the loop overhead h (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Tachocount
 
According to the Technical Reference, Tachocount counts the number of revolutions of the motor shafts (of the two built-in Cybermaster motors ONLY). I fiddled a liitle with it, but it doesn't seem too useful, first of all because the internal motors (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: Tachocount
 
At least there's one thing that CyberMaster proved - That 3 inputs is not the limit of the H8 or even all the LEGO PBricks. Clearly CyberMaster have 5 inputs, although 2 of them are fixed just like the 2 fixed motors (which is not as bad as it (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  RE: MindStorms at Robot Store (Hacking Lego Compatible Parts)
 
Here's a piece I could use: a touch sensor (switch) that is normally closed, with a diode in it. The diode could also be separate, in a brick with contacts on the top and the bottom, so you can stack the sensor, the diode, and your hookup wire. It (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  RE: Monitoring household power consumption
 
Actually, that little black band is a relic of earlier days when people (like myself) had jobs that occasionally required them to sit with a stopwatch and count turns. A slide rule was then used to calculate power consumption. Each meter had a (...) (28 years ago, 11-Nov-98, to lugnet.robotics.handyboard)
 
  Re: What about multiplexing sensors?
 
You can: 1. Put multiple Touch sensors on the same input but you can't tell which one was hit. 2. Put a Light and Touch sensor on the same input and read normal light levels except when the Touch is hit it the input will read 100. 3. There are a (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Handy Board PLease!!
 
If Anyone is selling ther Handy Board Please Tell me!! I rreeeaaally neeeeed it for some Science Proj..! thank you! (28 years ago, 11-Nov-98, to lugnet.robotics.handyboard)
 
  RE: What about multiplexing sensors?
 
I'm thinking more along the lines of using all three outputs and all three inputs to code a multi (read "more than three of each input and/or output") I/O multiplexor? This inherently reduces the possible sample rate on each input or output (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: What about multiplexing sensors?
 
(...) I've done it using an output port to control a MUX. I've been able to control up to three sensors through one input port. This could be extended to nine sensors through all three sensor ports. I'm working on ways to control more sensors both (...) (28 years ago, 11-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR