To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5141 (+10)
  Re: Monitoring household power consumption
 
(...) Good application, although it is a bit of a challenge. (...) Do you want to measure the individual devices, or the whole house? To do the individual devices you would have to have sensors right next to the devices. To monitor each circuit in (...) (28 years ago, 11-Nov-98, to lugnet.robotics.handyboard)
 
  Re: RCX Programming Questions and Sensor Ideas
 
(...) Paul, Are you sure you want to sleep before decrementing r31? As written, r31 is always >= 1 during the sleep -- which prevents any other tasks from obtaining a lock on the resource during this sleep time. In other words, once any two tasks (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: RCX Programming Questions and Sensor Ideas
 
(...) I think "oops" applies in this case. Your fix looks correct. (...) It doesn't have to be random, just each task needs a different delay. This is easy, since each task has to run its own version of the code. For task 3 insert 3 noops, for task (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: Ultrasonic Radar
 
(...) Polaroid manufactures the 6500 series ultrasonic ranging system that can be purchased in single quantities for less than $50 US, but it can't be directly connected to the RCX. (See (URL) for ordering. See ftp://wirz.com/Polar...r/6500.PDF for (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  What about multiplexing sensors?
 
Has anyone attempted to mux the three sensor connections to expand the RCX's sensor capability? Think this is possible? I don't have an RCX of my own [yet] nor the EE capacity to pull this off, so I'm counting on the geniuses out there! --Steve (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: MindStorms at Robot Store (Hacking Lego Compatible Parts)
 
I have some black ones as well, I think its for colour coding - yellow for sensors, black for third motor. I think I prefer the old grey cable as its more flexible. Perhaps the stiff thin black cable is supposed to last longer. On the Cybermaster (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: RCX Programming Questions and Sensor Ideas
 
(...) Does that support an arbitrary number of tasks? If there are n tasks numbered 1 to n, and task k delays for k cycles on failure, I think you still have to be careful to make sure that the number of tasks n is smaller than the loop overhead h (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Tachocount
 
According to the Technical Reference, Tachocount counts the number of revolutions of the motor shafts (of the two built-in Cybermaster motors ONLY). I fiddled a liitle with it, but it doesn't seem too useful, first of all because the internal motors (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: Tachocount
 
At least there's one thing that CyberMaster proved - That 3 inputs is not the limit of the H8 or even all the LEGO PBricks. Clearly CyberMaster have 5 inputs, although 2 of them are fixed just like the 2 fixed motors (which is not as bad as it (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  RE: MindStorms at Robot Store (Hacking Lego Compatible Parts)
 
Here's a piece I could use: a touch sensor (switch) that is normally closed, with a diode in it. The diode could also be separate, in a brick with contacts on the top and the bottom, so you can stack the sensor, the diode, and your hookup wire. It (...) (28 years ago, 11-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR