To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4871 (+10)
  Re: IR Detection
 
Hi Most of the IR LED's sold at Radio Shack are the 840-880 nm wavelenght type. The Sharp tin can requires the 940 nm wavelength IR beam if my memory serves me right, it also requires to be modulated at 38 or 40 kHz depending on the model. This 38 (...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Automated brick sorter
 
Huw, Very nice job. I saw that you used a clutch gear. On thing I've been experimenting with is replacing a clutch gear with a pair of motors, one working like a generator to drive the other. This only works well if the generator-half is one of the (...) (28 years ago, 2-Nov-98, to lugnet.robotics)
 
  Re: Bend/ Flex Sensor
 
I think its cheaper to get an old Nintendo power glove and Hack it! (...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  Re: programming help.
 
The "<<" is a shift left operator in C 0E is the actual motor port on the Handy Board. (...) mean? (...) between 4 and 7. (...) peek(address) | value). I don't have any documentation here, so I don't know what is stored in 0x0e, but it could be the (...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Voltage for the DC motor
 
Ja, I could not tell you for the life of me what 'type' f a HB it is, but I remember someone once telling me that you could just remove one of the pins from the driver chip instead. This method would be less final (ie, just bend the lead up and if (...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  Welcome newbees
 
There are many web pages offering useful info on lego-robotics, but to my knowledge there are currently two web pages specifically set up as convenient entry points if you're new to lego-robotics. Legorobotics page This page gives an overview of (...) (28 years ago, 2-Nov-98, to lugnet.robotics)
 
  Re: DC motor voltage source
 
Philip: I depends on how many motor driver ports you want to have on the new voltage. If you have just two motors, then lifting (and wirewrapping) pin 8 for one chip whould be enough. The motor outputs affected are nearest to the chip modified. I (...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  Line follower kit
 
I was wondering if anybody had used the Line follower kit from the robotstore? Is it pretty much plug and play (besides a little programming) for the handyboard? Thanks. Dave (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  robot navigation.
 
Hi all, My robot has come to the stage where its time to start writing the basic navigation routines. I have two encoders on each rear drive wheel and two caster type wheels on the front.I have been trying to put some basic software modules together (...) (28 years ago, 2-Nov-98, to lugnet.robotics.handyboard)
 
  Using sonar to approximate RADAR?
 
Hello, all: <DELURK> I've been following this list for some time now, but since I didn't have an HB, I didn't contribute to the discussion. Now, I've just ordered my HB because I plan to start building. But I have a question... I have a model police (...) (28 years ago, 3-Nov-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR