 | | Re: the LEGO CNC-Machine
|
|
the motor in the movie is called a "power motor", you can read about it here: (URL) the large black one with red axleholes. i'll be using it as the spindle. i guess the gearing in my axes is still too fast for the cutter, if i have to redesign the (...) (17 years ago, 4-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"Bob Fay" <rgfay@earthlink.net> wrote in message news:Jnt8MF.n84@lugnet.com... (...) This is one of mine. Note the left worm is out if sequence by 1/4 turn with the other two. this is putting pressure on the dual racks to remove the backlash. (URL) (...) (17 years ago, 3-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:Jnt54J.Jpy@lugnet.com... (...) I liked the technic beams because I could lock them together. I imagine double wide bricks can make a good foundation. Put an ocassional beam in to allow (...) (17 years ago, 3-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
(...) thanks! it's nice to get that kind of feedback from someone who's not new to lego mills :) (...) yes. you can see it in my diagrams again, the cutter hangs over the table pretty far: (URL) i'm not sure yet how exactly i will manage to make it (...) (17 years ago, 3-Sep-07, to lugnet.robotics.rcx, FTX)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:Jnszy4.7qA@lugnet.com... (...) very well done. Your slider design is also very good. The table is supported in all directions. You have made it simple and effective. Good engineering! (...) (17 years ago, 3-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: pbLua GUI ???
|
|
(...) This is starting to look pretty promising as a standard IDE. I will do my part and install Eclipse here and get the instructions updated from Christian's instructions. Once we get a decent IDE the pbLua system may be almost ready for "everyone (...) (17 years ago, 3-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: pbLua GUI ???
|
|
(...) ;-) currently I'm extending Eclipse with simple terminalprogram and pbLuaAPI... With pbLuaAPI-Wrapper(maps pbLua nxt.* to native Lua routines) you can test and run pbLua code at local PC before transfering to NXT... Christian (17 years ago, 3-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: the LEGO CNC-Machine
|
|
i uploaded a little video of the first tests with the x and y axes. check it out here: (URL) trying out wax and soap as cutting materials, i'll report again when i'Ve tested some more :) (17 years ago, 3-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: pbLua GUI ???
|
|
Zitat von Christian Mock <chrimo-@-moccy.xdsnet.de>: (...) pbLua/NXT support there is rather sparse, isn't? Matthias "why don't I do that myself, though?" ---...--- This message was sent using IMP, the Internet Messaging Program. (17 years ago, 3-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: Ooops! NXT Software Comparison correction
|
|
I can further manipulate the numbers for this timing test by using the enhanced standard firmware's support for adjusting a thread's priority. Here's the results when I tweak priorities: W/O LCD LCD Priorities ---...--- 50617 22608 40/5 63211 27375 (...) (17 years ago, 2-Sep-07, to lugnet.robotics.nxt)
|
