 | | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:Jnp0Cy.2CJ@lugnet.com... (...) This X axis gear box is loaded so there is no backlash. The 16T gear on the right side has a hole through it and is fixed to the shaft with a serrated half (...) (17 years ago, 1-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Ooops! NXT Software Comparison correction
|
|
My bad. When I fiddled with the pbLua code I forgot to turn on the motors and neglected to change the Motor A speed. So when you ran the program, the motors didn't move. I also had uploaded the wrong version to my web site of the version that shows (...) (17 years ago, 1-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: the LEGO CNC-Machine
|
|
(...) 16t gear to the gear rack on the bottom of the table. also, the z axis seems to use an idler gear. that's exactly the setup i've built, you can see it here: (URL) top left, next to the tool changer idea (right next to the tiny word "tool"). i (...) (17 years ago, 1-Sep-07, to lugnet.robotics.rcx)
|
| |
| | pbLua GUI ???
|
|
Hi, do you think pbLua needs an IDE/GUI for development ? Normaly, pbLua just needs a working terminal emulation for development... BUT, I've learned from Lego-NXT-Users: that's not enough, NBC/NXC has "bricxcc" !!! pbLua has more than ONE GUI for (...) (17 years ago, 31-Aug-07, to lugnet.robotics.nxt)
|
| |
| | Re: pbLua Beta 13c Team Hassenplug NXT Software Comparison Results
|
|
"Ralph Hempel" <rhempel@bmts.com> wrote in message news:46D819C6.700000...mts.com... (...) Ralph, Feel free to pull and reformat the code. You should be the primary credit. I just fiddled around, and I expect that a bit of tweaking by you will (...) (17 years ago, 31-Aug-07, to lugnet.robotics.nxt)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:JnMwFu.CMs@lugnet.com... (...) I like the worm for a drive. It provides the best ratio and the least backlash. It also acts as a brake while the slide is under the pressure returned by (...) (17 years ago, 31-Aug-07, to lugnet.robotics.rcx)
|
| |
| | Re: pbLua Beta 13c Team Hassenplug NXT Software Comparison Results
|
|
(...) Walt, Thanks a LOT for updating the example. Do you mind if I pull the code from your site, reformat if necessary and include it in the test code section of my distribution? You will, of course, retain primary credit in the source file. This (...) (17 years ago, 31-Aug-07, to lugnet.robotics.nxt)
|
| |
| | Re: the LEGO CNC-Machine
|
|
ok, now i understand what you mean. the problem is that this setup could be difficult for long axes, i guess the axle with the worm gears would flex too much... (...) exactly what i was thinking. that's the way the machines i've seen change their (...) (17 years ago, 31-Aug-07, to lugnet.robotics.rcx)
|
| |
| | Re: Update: Team Hassenplug NXT Software Comparison Results
|
|
(...) Thanks Steve for listing up LEJOS OSEK too! LEJOS OSEK V1.04 also supports Bluetooth based data logging with NXT GamePad. (17 years ago, 30-Aug-07, to lugnet.robotics.nxt)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:JnL3ox.7r9@lugnet.com... (...) As you can see, I do not know how to get "deep links" on Brick Shelf. If I figure it out I will post the links again. The tools can ride a disk in front of (...) (17 years ago, 30-Aug-07, to lugnet.robotics.rcx)
|
