 | | Re: Brickworld 2007 - Indy 5.00
|
|
(...) Okay, I'm confused. How can an 8' x 10' track be centered on a 4' by 8' surface? What is the actual width of the track? If the whole track fits on a 4' x 8' surface, then I would assume the width must be less then 2'. Gus (17 years ago, 17-Jun-07, to lugnet.events.brickworld, lugnet.robotics)
|
| |
| | Re: Shutdown/Off while program running crashes BrickOS
|
|
(...) Yes, that should be the latest version. (...) That is correct. You shouldn't need to do anything else. At one point, I made some changes to the firmware so the program could also access the run button. But, normally all that is handled in the (...) (17 years ago, 17-Jun-07, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Shutdown/Off while program running crashes BrickOS
|
|
(...) I'm using what appears to be called BrickOS 0.9.0. It was installed using John Hansen's simplified installation from his BricxCC sourceforge site. I was under the impression that on later versions of BrickOS, like what I am using, the firmware (...) (17 years ago, 17-Jun-07, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Shutdown/Off while program running crashes BrickOS
|
|
(...) Gus, It sounds like the code is testing for pressing the run button, but not pressing the power button. I would think testing for shutdown would be good enough, but who knows... :) What version of BrickOS are you using? I'd be glad to take a (...) (17 years ago, 17-Jun-07, to lugnet.robotics.rcx.legos)
|
| |
| | Shutdown/Off while program running crashes BrickOS
|
|
I have a big and somewhat complicated BrickOS program that I believe is reasonably well behaved. All my loops monitor shutdown_requested and I have tested stopping the program with the Run button while the program is in various states and it always (...) (17 years ago, 16-Jun-07, to lugnet.robotics.rcx.legos)
|
| |
| | Re: problem with rcx 2.0
|
|
(...) There is a good chance that the culprit is the entry fuse of the board. Check it with an ohmeter... This fuse is a tiny SMD one, rated 1.5A fast blow. It can be seen on this photo ((URL) in the lower right corner, between the long grey (...) (17 years ago, 14-Jun-07, to lugnet.robotics)
|
| |
| | Ultimate Builders Set instructions
|
|
I am looking for a copy of the instructions for the plotter found in the Ultimate Builders Set. Peeron does not have instructions for this set. Does anyone have a copy (or even an LDRAW dat file of the plotter would probably do) (17 years ago, 14-Jun-07, to lugnet.robotics)
|
| |
| | problem with rcx 2.0
|
|
Unfortunately, while working with the rcx open, a little piece of metal fall between the pins of the chip with a 16M6 written on top. It is to the left of the big capacitor and close to the small one. Has four legs, three in the front and one in the (...) (17 years ago, 13-Jun-07, to lugnet.robotics)
|
| |
| | pbLua BT Code
|
|
Hello community, has anybody a working code for pbLua ? I've tried to connect from NXT-pbLua to remote WindowsMobileDevice, but no success... What is the correct way to connect to remote devices ? 1.how is the peering of both partner done ? 2.how (...) (17 years ago, 13-Jun-07, to lugnet.robotics.nxt)
|
| |
| | RoboLab
|
|
Have a great Summer Tom Lohre’s Quarterly Art Show at Med+ Opening July 14th, 2007 from 6:30 to 9 PM, light refreshments served. In the lobby of Med+ Urgent Care, 9549 Montgomery Rd. Suite 100, Cincinnati, OH 45242, 513-489-3737, just north of (...) (17 years ago, 12-Jun-07, to lugnet.robotics.rcx.robolab)
|
