 | | RE: About the elsema FMTR 2705
|
|
Michael, I have tried to use the Elsema radios without the modem chips but because 27Mhz is such a noisy frequency (at least here in Australia) I found that I got way to much interference when interfacing directly to TTL. The modem chips are really (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | driving stepper motors
|
|
Hi all, I have nearly completed building my handy board and have come across a couple of stepper motors that i would like to use to drive my robot. Motor spec's are :- 2 Phase 6V 1.2A 1.8Deg step Is there any way of interfacing the handy board to (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Current supply
|
|
Hallo Holger, Spezifikationen über die 68HC Familie kannst Du direkt über Motorola beziehen. Ich habe dort das "Pink-Book" kostenlos bekommen, Du must Dich lediglich mit der Literaturabteilung verbinden lassen (Ich habe für die 68HC11A0-A8) das Buch (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Extreme Creatures, Cybermasters, etc?
|
|
(...) I dunno that much about the technical side of MS or CM. As has been pointed out already, CM is made for playing to a larger extent than MS. I'd still say CM is rather good, though, and quite worthwile. It's probably a good alternative to the (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Extreme Creatures, Cybermasters, etc?
|
|
(...) They looked interesting in the pictures I've seen. Can you describe them more? (28 years ago, 8-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Extreme Creatures, Cybermasters, etc?
|
|
(...) Well, there are five yellow wheels on each side, and the tread goes round them. The wheels are probably as large as the medium pulley and one stud wide, with a narrow but deep groove in the center to keep the treads on track. The treads are (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
|
| |
 | | driving stepper motors
|
|
Hi all, I have nearly completed building my handy board and have come across a couple of stepper motors that i would like to use to drive my robot. Motor spec's are :- 2 Phase 6V 1.2A 1.8Deg step Is there any way of interfacing the handy board to (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: driving stepper motors
|
|
Look up the datasheet for the SGS-Thomson L297, they have a complete circuit diagram for a stepper motor driver there. (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Extreme Creatures, Cybermasters, etc?
|
|
(...) ok, wasn't sure about that. (28 years ago, 8-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Extreme Creatures, Cybermasters, etc?
|
|
(...) But you could use the treads without, yeah? I'd really like some better treads, as the ones that come in Mindstorms RIS, Tread Trekker, and Mountain Rambler are too small for a lot of things. (Particularly, hard to power and still have a lot (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
|