To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *43669 (-20)
  Re: NXT - ARM7's and USB
 
(...) or does Lego mean: - the USB controler can transport data bidirectional (how can it otherwise check the transmitted data) and - the USB controler is a Slave (can only be connected to a USB-Master, in general something big as a PC) Stef (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) I was wondering if one could make a two port host device with its own power source (battries). It could be relatively simple, where one host port polls the device port of the NXT to find out if there is anything to do, and then the second host (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: NXT - ARM7's and USB
 
(...) Chris, I know little about USB, but USB communication is not peer to peer like an ethernet port. You have masters and slaves, or hosts and devices. Whether you are host or device, you still need to be able to communicate bidirectionally. If (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  NXT power (was memory, prog. langs etc)
 
My 2c based on some experience with high-level robotics programming (vision, navigation & mapping, etc): While it is concievable that you could write some sophisticated mapping and analytic software on this platform, it will require deep low-level (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: NXT - ARM7's and USB
 
(...) Hopefully an answer (I don't have 3...). The actual micro doesn't have the full hardware needed to implement communications. You still need to include transceiver/receiver hardware that acts as the bridge between the cable and the micro. Lego (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) This all makes some sense, though it seems strange to put a digital board in the servos, but not do the control there. In any case, I think my first project will be to figure out how to use the USB port to connect the NXT to a more powerful (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) Isn't there an inherent problem with this idea? If the NXT is a slave device, it is a power consumer, right? That would imply that if you connected a USB storage device, the device would not get power, since the NXT won't have been designed to (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Where should the 100 NXT testers' findings be shown?
 
Is it likely that all 100 of the people chosen for early NXT testing will know of LUGNET and post their findings here? Should LEGO set up a forum on legofan.org or mindstorms.com? How about nxtbot.com? It would be nice to have a single place to get (...) (21 years ago, 8-Jan-06, to lugnet.robotics, lugnet.technic, lugnet.dear-lego, FTX)  
 
  Re: Mindstorms NXT programming languages
 
(...) Besides trying to hack the USB port to make it a host (which seems more unlikely the more I read), and besides trying to use Bluetooth to talk to my Gameboy Advance (and vice-versa), I'd also like to tackle something like the RCX.NET project. (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) I'm talking about stuff like this: (URL) for the start-up pack, which is for eight paired students. The Team Challenge with USB set is $200, and you get four of them. That's still just $800, so there's another $450 worth of stuff. 4 extra (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: multiplexing Spybot inputs?
 
(...) Some time ago, I have sugested the use of the VLL port to make an interface to connect a couple of lego light sensors to the spybot. The ideea was to have an analog device (powered by a 9V bov) that would just switch on a sensor, then switch (...) (21 years ago, 8-Jan-06, to lugnet.robotics.spybotics, FTX)
 
  NXT - ARM7's and USB
 
Im not a chip guru, can someone explain why the lego speck says the USB is input only? The PDF's for the ARM7 chip set(s) this could be, state the on board USB controller is bidirectional. questions, questions, questions..... Chris (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: Mindstorms NXT programming languages
 
Hi Brian, (...) On the RCX Lejos is about that much faster than the standard firmware, and we have 1ms timer resolution. (...) You also get those in Lejos, and compared to NQC it can access more memory. Jürgen (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) I just saw Lego's definiton of a servo motor. It resembles a industry servo, not a hobby servo. In the hobby servo, the closed loop is done in the servo electronics, but in the industry servo, the closed loop is done in the controller. (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
I am not very familiar with the NXT platform but as it sounds now could you possibly plug a USB Flash memory stick into the USB port (or connector) on the NXT and use it for data storage? - John (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT and memory
 
(...) In the case of room mapping, would speed be so important? Isn't it it in the ms range? (A lot compared to an instruction cycle, but good enough for a moving bot) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT and memory
 
(...) You could use a bit per square inch (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) I bought my mindstorms from pitsco to save $50... (cost $150) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: Mindstorms NXT programming languages
 
(...) Actually, when using the standard firmware speed is very much a concern with the RCX for me... and others, if things like the Swan firmware are anything to go by. Currently, using NQC, I need to examine the bytecode generated to try to (...) (21 years ago, 8-Jan-06, to lugnet.robotics)
 
  Re: new Mindstorms servos?
 
(...) Although I think there's two things to watch out for here. First, if you have continuous monitoring of the encoders, you could have speed control (in other words, the speed in the video may not be the maximum, but something less). Second, (...) (21 years ago, 8-Jan-06, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR