 | | Re: train precision
|
|
(...) didn't find the c code in the url you mentioned. You used the same technique in the train, as in the legway? daniel (21 years ago, 29-Dec-05, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: train precision
|
|
(...) thanks for the suggestion, Brian I want to make some experimences with LDCC some day. But not in this project. daniel (21 years ago, 29-Dec-05, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: train precision
|
|
(...) ... (...) ... (...) ... (...) As Brian said, it's not the motors, it's the RCX. You can run Technic motors off a train controller, and you can vary the speed. But you need to do a bit more if you're using the RCX. We used that scheme when we (...) (21 years ago, 29-Dec-05, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: train precision
|
|
I do think Steve is on the right track here. The train regulator varies the voltage, but the RCX output can't. So you are left with managing (nominally) 9v pulses. But there is another solution. You could add a DCC decoder to your train motor, and (...) (21 years ago, 29-Dec-05, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: train precision
|
|
(...) hi Steve, I think the problem is not exactly the same. The lego technic motors run always at the same speed so you need to use that kind of schema for speed control in robots. The train motors are different, they have a speed proportional to (...) (21 years ago, 29-Dec-05, to lugnet.robotics.rcx.legos)
|
| |
 | | LASM Question
|
|
Hi, How can I use sensors in Visual Basic using the LASM Command I wan to sense touch on input port 1 Also where can I find complete doc for LASM. Thx SQ (21 years ago, 28-Dec-05, to lugnet.robotics)
|
| |
 | | Re: train precision
|
|
(...) Daniel, One problem you'll run into with most software is that it switches between power and float to adjust the motor levels. It works much better to switch between power and brake. Using most software, the train will continue to speed up, (...) (21 years ago, 27-Dec-05, to lugnet.robotics.rcx.legos)
|
| |
 | | train precision
|
|
A couple of years ago, i used brickOS. Then, i changed to Lejos... I have a moc where i use the RCX to control a train with a lego train motor. It is difficult to control the train with LejOS, because it only has 8 output levels. Two solve the (...) (21 years ago, 27-Dec-05, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Lego "style" wire and electrical connectors
|
|
(...) Right- I shaved off two of the studs with a paring knife (opposite corners), then the screws just twisted right in. I said 3/4" before, but that's too long. Maybe 1/2-inch? Take a brick with you. I found them at Radio Shack, though, I know (...) (21 years ago, 27-Dec-05, to lugnet.robotics)
|
| |
 | | Re: Lego "style" wire and electrical connectors
|
|
(...) Unfortunately I've triec radio shack for the wire and other parts like LEDs and was worely disappointed. I recently got some reed switches mail-order and am hoping to get at that soon. Not sure how to find a well stocked local electronics (...) (21 years ago, 27-Dec-05, to lugnet.robotics)
|
| |
 | | Re: Lego "style" wire and electrical connectors
|
|
(...) Hello Tim, In what way did you use the machine screws? Did they replace studs say on a 2x2 brick? were you abel to stick them up inside the stud? Any pics or further instructions? I'm in serious doubt aboutmy skill of crafting a function *and* (...) (21 years ago, 27-Dec-05, to lugnet.robotics)
|
| |
 | | Re: Lego "style" wire and electrical connectors
|
|
(...) Somehow, even though it was the same one and in theory was loosened a bit, I mangled it a bit... and also had trouble getting it back together with the wires making good contact with the metal. Thanks for the link. -Ken (21 years ago, 27-Dec-05, to lugnet.robotics)
|
| |
 | | Re: Remington: my Brickfest05 Super-Mega Sumobot
|
|
Steve/All, I just found this followup; I'd somehow missed it back in October. Many apologies, please don't read anything into the delay... (...) Yes, the roller is intended to detect (lack of) motion. It turns out it didn't help me much in the (...) (21 years ago, 27-Dec-05, to lugnet.robotics)
|
| |
 | | Re: color sensor
|
|
(...) Happy Christmas to you too! ... and yes, I have a bench prototype running using that TAOS chip. As per my previous attempts at a color sensor however, it is proving very difficult to make the sensor range and orientation independent. JB (21 years ago, 25-Dec-05, to lugnet.robotics.rcx)
|
| |
 | | color sensor
|
|
hi all, first for all a happy christmas to everybody. I just ran into this nice looking color sensor TCS230, which might be useful for detecting Lego colors. (URL) Mientki (21 years ago, 25-Dec-05, to lugnet.robotics.rcx)
|
| |
 | | Re: what batteries
|
|
Robert, I've had a lot of good luck with Energizer batteries, but have also used some of the higher 2200+ mah brands. All seem to work well with the RCX. The only thing to be aware of is mixing batteries. If you have 5 with a 2200mah rating and one (...) (21 years ago, 24-Dec-05, to lugnet.robotics)
|
| |
 | | Re: mindscript - subroutines
|
|
(...) Your code works fine for the Spybot target. RCX2 and earlier brick types do not support defining subroutines in MindScript. This is documented in the VPBrick API help file which you can access from within BricxCC. Just press the context (...) (21 years ago, 23-Dec-05, to lugnet.robotics)
|
| |
 | | Re: mindscript - subroutines
|
|
(...) Ron, I am fairly new to the mindscript language as well, but I have done substantial research into this problem as I was encountering the exact same problem. From what I have found, you cannot do user subroutines in mindscript FOR THE RCX. (...) (21 years ago, 23-Dec-05, to lugnet.robotics)
|
| |
 | | earlier version of binutils?
|
|
Hi, I have been trying to get brickos to compile on my linux machine. I followed the instructions here: (URL) used binutils version 2.16.1, and gcc version 4.0.2. The cross compile seemed to work. However, when I try to compile brickos, I get the (...) (21 years ago, 22-Dec-05, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: 4x4 Buggy
|
|
(...) At most, you won't have the [probably negligible] losses of a transmission. However, if the output is limited to, say, 1A, there's no magical way the sum of currents all motors will exceed 1A. Maybe if they aren't running near that current, (...) (21 years ago, 23-Dec-05, to lugnet.robotics)
|