To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *42944 (-10)
  ROBOLAB Questions
 
Why does ROBOLAB not turn the motors off after a "wait for..." direction? Almost every program that I have written with ROBOLAB has had issues with motors not turning off when they were supposed to. As an example: I have a program that drives one (...) (21 years ago, 23-Sep-05, to lugnet.robotics)
 
  WebCamBot
 
Though I don't have the Web setup yet, I have a fully operational webcam robot that will hopefully be internet-controllable in the near future (think, by the end of next year, maybe, if IB tests and extended essay don't get in the way!). The ruler (...) (21 years ago, 23-Sep-05, to lugnet.robotics, lugnet.technic, FTX)
 
  Re: Rotating through a four-bit nibble
 
(...) Kev (...) Nice to hear from another bit twiddler.... (...) I do find it ironic that the firmware suports bitwise AND and OR, but not XOR, and also not shifts. Gack! Well, at least we're not having to use loops to add things to themselves to (...) (21 years ago, 22-Sep-05, to lugnet.robotics, FTX)
 
  Re: Rotating through a four-bit nibble
 
(...) Understand what better? Binary math? No problems with that! By "backwards" I meant that multiplication and division by powers of 2 are usually changed to shift L/R by compilers. Also, I am amused that because the firmware doesn't use the (...) (21 years ago, 22-Sep-05, to lugnet.robotics, FTX)
 
  Re: Rotating through a four-bit nibble
 
(...) BrickOS has mocked me from the horizon for some time, but there are two things that are holding me back: (a) Judging by the posts and what I've read, the learning curve seems awfully steep - especially since I'm on a Mac. (b) Rarely have I (...) (21 years ago, 22-Sep-05, to lugnet.robotics)
 
  Re: Could we all let it alone? (Was Re: Moonbase Module - Mech Bay 07)
 
(...) <major snippage (down to the tech)> Thanks Eric, I appretiate the reply. I have seen a few posts here and there that I find personally irrelevant - and mreely pass them by. I have also occasionally been attacked by posters. In my case it has (...) (21 years ago, 22-Sep-05, to lugnet.build.mecha, lugnet.robotics)
 
  Re: Rotating through a four-bit nibble
 
(...) Maybe it is time to move on to BrickOS? int rotate_right( int value, // the value to be rotated int width, // the width of the rotated field int base, // bitnumber of rightmost bit in rotate field int amount) // the amount to rotate between (...) (21 years ago, 22-Sep-05, to lugnet.robotics)
 
  Re: Rotating through a four-bit nibble
 
(...) Both your 1st & 2nd solutions are very good; thanks to you and other posters to this thread for giving me a much better handle on binary manipulations, and solutions to this problem. In answer to an earlier question, speed is important (simple (...) (21 years ago, 22-Sep-05, to lugnet.robotics)
 
  Re: A LEGO double-throw switch?
 
(...) First, I learned a *lot*, so thank you all. As for which "solution" I ended up using, first disclaimer, I've not yet built a "crate conveyor". But some prototyping showed that the tank treads just have too much bending friction for what I (...) (21 years ago, 22-Sep-05, to lugnet.robotics)
 
  Swan scheduling bug?
 
I'm starting to use the swan firmware and I'm having a problem with the scheduling. It seems like a task with a long wait does not yield properly to other tasks. Here the NQC code sample: task taska() { WaitMS(150); AddToDatalog(9900); } task main() (...) (21 years ago, 22-Sep-05, to lugnet.robotics.rcx)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR