 | | Re: self-propagating RCX program
|
| (...) Agreed. I was hoping for much, much more. Specificly, by this definition, I strongly doubt the claim that this is the "first ever" self-reproduction. Some of the mechanical models from a long time ago were similar in concept, but with a (...) (21 years ago, 13-Sep-05, to lugnet.robotics)
| | |  | | RCX to RCX NQC
|
| In a semi-followup to Steve's earlier "remote battery tester"... While the standard firmware provides almost no way to get bytes into the RCX (other than "Message()", one byte at a time), it can certainly export them ("SendSerial"). And it occured (...) (21 years ago, 13-Sep-05, to lugnet.robotics.rcx)
| | |  | | VEX
|
| I can't seem to find a lugnet.robotics.otherbrand group, so I will ask here; Has anyone taken a VEX set for a test drive? I haven't, mainly 'cos of the cost versus what you seem to get for the money. Any comments would be welcome. FUT to somewhere (...) (21 years ago, 13-Sep-05, to lugnet.robotics)
| | |  | | direct manipulation of bits in RCX registers using NQC
|
| Hi all, Can anyone tell me if it is possible to use NQC to directly set bits in RCX registers? And if so, how does one do it? I've seen C code examples of this in a few places, but no NQC examples. Specifically, I want to turn on and off the red (...) (21 years ago, 12-Sep-05, to lugnet.robotics.rcx.nqc)
| | |  | | Re: Mana Cat
|
| Congratulations Eric! Maybe this is the dawn of those outside of the hobby taking Lego seriously as a tool for creating sculptures and robots. I will admit being disappointed to see such a promising project left, but then I am still heartened to (...) (21 years ago, 12-Sep-05, to lugnet.technic, lugnet.robotics, lugnet.build.mecha)
| | |  | | Re: 1.0 brick not responding
|
| (...) Tammy, A couple questions... 1) Does the light on the IR tower flash when you're trying to communicate? 2) Did it ever work (did it work before, but stop, or is this the first time you've tried communicating?) 3) What are you trying to (...) (21 years ago, 12-Sep-05, to lugnet.robotics.rcx)
| | |  | | Re: Speed Computer
|
| (...) With a rotation sensor and an RCX, you can do the same thing for free with a four or five line NQC program. In fact, you can do better. With two rotation sensors and an RCX you can dyno two motors at the same time - guaranteeing that you have (...) (21 years ago, 12-Sep-05, to lugnet.robotics)
| | |  | | 1.0 brick not responding
|
| mac powerbook 5300 communicates with the IR tower, but no response from the brick. palm 130 with pbrick, also no response from the brick. The brick powers on and beeps, just no communication with the powerbook or the palm for programming. Since it (...) (21 years ago, 12-Sep-05, to lugnet.robotics.rcx)
| | |  | | Re: Speed Computer
|
| (...) It was on sale at S@H a couple of months ago for 50% off. I'd say if you need one, $10 is a good price. Unless you have a real need, I think $20 is too much. I have had one for a couple of years and I use it for one purpose only, dyno-ing (...) (21 years ago, 12-Sep-05, to lugnet.robotics)
| | |  | | Speed Computer
|
| I was just wondering if anyone has one of these speed computers (URL). Also, if you have one, is it worth the US$20.00 that is asked for it? I am considering getting one, but was told several years ago by a friend that it was a waste of money. (...) (21 years ago, 11-Sep-05, to lugnet.robotics)
| |