 | | RE: sub-vi begin vs end control
|
|
Hi Tom, Just for my education purpose, I'd like to understand the difference between the "begin" & "end" control boxes at the "Front Panel" window. Although they look identical, they must be different since they failed to wire to the blocks next to (...) (22 years ago, 16-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx)
|
| |
 | | Re: sub-vi begin vs end control
|
|
(...) It is a leftover from LabVIEW. When you create a sub.vi, LabVIEW reuses the name of whatever is wired to the control/indicator. This behavior makes perfect sense in LabVIEW but much less so in Robolab. FWIW, the names are little more than (...) (22 years ago, 16-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx)
|
| |
 | | sub-vi begin vs end control
|
|
Hi, After a sub-vi is created, there are two controls created namely begin and end. Would someone explain why they are backwards? That means, it creates an "end" control linked to the beginning of the sub-vi, while the "begin" at the end. Thank in (...) (22 years ago, 16-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx)
|
| |
 | | Re: MOC: Egglift, a Lego Appliance to cook soft-boiled eggs
|
|
(...) Thanks! And from the other post ((URL)), it appears that the ABS will start to give way around 80 deg Celsius. Btw, I think your invention could also do hot dogs and bacon rashers for a fuller breakfast ;-) CS (22 years ago, 16-Jan-05, to lugnet.robotics, FTX)
|
| |
 | | Re: MOC: Egglift, a Lego Appliance to cook soft-boiled eggs
|
|
(...) (snipped pic) (...) This one? (URL) "The Gaklander" (22 years ago, 15-Jan-05, to lugnet.robotics, FTX)
|
| |
 | | Re: MOC: Egglift, a Lego Appliance to cook soft-boiled eggs
|
|
(...) The range of the Lego temperature Sensor is -20o C to 70 o C. You can see one reading below. As you can see, I'm almost off limit. (URL) (...) From my test, definitely the sensor would go off range first. Probably that's the reason why TLC (...) (22 years ago, 15-Jan-05, to lugnet.robotics, FTX)
|
| |
 | | Re: Technic plates
|
|
(...) The shank with the dimension is galled up but it fits the 3/16" hole in the bit racks - I've got more than a few sets of drill bits and loose ones hanging around. I simply looked for the bit that provided a good fit (no slop) in a stack of 8 (...) (22 years ago, 15-Jan-05, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: MOC: Egglift, a Lego Appliance to cook soft-boiled eggs
|
|
(...) Phew, I can feel the heat! What was the reading recorded by the temperature sensor? As I recall the LEGO Temperature sensor range is from -20 degrees Celsius to +50 degrees Celsius. Would the sensor go off range or would the ABS melt first? CS (22 years ago, 15-Jan-05, to lugnet.robotics, FTX)
|
| |
 | | Re: MOC: Egglift, a Lego Appliance to cook soft-boiled eggs
|
|
(...) I think it was 'Ben' Beneke if thats any help, but his site has moved fairly recently. Tim (22 years ago, 15-Jan-05, to lugnet.robotics, FTX)
|
| |
 | | Re: Technic plates
|
|
As I might have noticed, the Lego technic holes are exactly 4.8mm. This technique is also good to create "technic bricks" - very usable when you need a more stabilized axle-guide. Just drill a standar 2X* brick through the cilinders from the bottom, (...) (22 years ago, 14-Jan-05, to lugnet.robotics)
|