 | | Re: Help installing brickOS
|
|
(...) Sure. The configure script tries to find the gcc cross compiler toolchain for the brick's hitachi processor. This chain is needed to compile brickOS to a program that can be run by the RCX. But it seems that you did not install the tool chain. (...) (22 years ago, 28-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
 | | BricxCC 'Float' Command not working on Scout
|
|
While programming a Scout using BrickCC, no matter how many times I tried, I could not get the Scout to 'float' its motors. The program was as follows- task main() { OnFwd(OUT_A); Wait(50); Float(OUT_A); } After a half second the motor would brake, (...) (22 years ago, 28-Oct-04, to lugnet.robotics)
|
| |
 | | Re: Help installing brickOS
|
|
(...) I believe that I had the exact same problem a few weeks ago, but I found that using a pre-built package takes a lot of the hassle out of installing BrickOS. The pre-built packages can be found at: (URL) hope this helps, Timothy (22 years ago, 27-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
 | | Help installing brickOS
|
|
I'm trying to install brickOS 0.2.6.10.6 on WIN NT. After unning "configure" it's busy for along time, and terminates with the message -"No Hitachi gcc compiler found. Please install compiler and try again." Any suggestions? Thanks, Jordon (22 years ago, 27-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
 | | GASTON
|
|
Hi all, 1. Finally most of the documents, building instructions, schematics and so on are available concerning our robot GASTON (URL) Ultimate Robolab is advancing well and will soon be available for beta-testing: (URL) (22 years ago, 27-Oct-04, to lugnet.robotics)
|
| |
 | | Re: Compound shaft
|
|
(...) You could use a differential - or maybe a large turntable. ---...--- Steve Baker ---...--- HomeEmail: <sjbaker1@airmail.net> WorkEmail: <sjbaker@link.com> HomePage : (URL) : (4 URLs) GEEK CODE BLOCK----- GCS d-- s:+ a+ C++++$ UL+++$ P--- (...) (22 years ago, 27-Oct-04, to lugnet.robotics)
|
| |
 | | Re: Piggybacking sensors, but in a different way
|
|
(...) While you may be able to connect a touch sensor (passive) to two RCXs, I doubt that would work with a light sensor (any active sensor). Mainly, because one of them must be set to power the sensor. Normally, when the sensor is read by an RCX, (...) (22 years ago, 26-Oct-04, to lugnet.robotics.rcx)
|
| |
 | | Re: 1Wire vs I2C
|
|
On Tue, 26 Oct 2004 18:19:36 GMT, Bruce Boyes <lego-robotics@crynwr.com> wrote: Big Snip! (...) Whew! Thanks for the insight! How does the component/driver cost compare? -Rob. (22 years ago, 26-Oct-04, to lugnet.robotics)
|
| |
 | | 1Wire vs I2C
|
|
(...) I2C is much faster (100 Kbit I2C is the slowest, vs 14 Kbit 1Wire), more reliable, but much shorter distance. Newer I2C can be 1 Mbit or more. (...) 1Wire will never do 115 kbits reliably. The 1Wire overdrive option is not reliable and few (...) (22 years ago, 26-Oct-04, to lugnet.robotics)
|
| |
 | | Re: Compound shaft
|
|
(...) An example of this is here: (URL) using (URL) that can engage with any of the technic 1x plates : 2719 Technic Plate 1 x 10 with Holes 4263 Technic Plate 1 x 4 with Holes 4262 Technic Plate 1 x 6 with Holes 4442 Technic Plate 1 x 8 with Holes (...) (22 years ago, 26-Oct-04, to lugnet.robotics)
|