To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *40464 (-10)
  RCX firmware vs hardware
 
All, I've got an RCX 1.0, and my son has a 1.5. Is there anything that would cause problems if I loaded 1.5 firmware into a 1.0 RCX? While on the topic, what about 2.0 firmware in a 1.0 RCX? (22 years ago, 6-Jul-04, to lugnet.robotics)
 
  Re: train control
 
Hi Daniel, (...) sorry to reply so late, I wanted to try it myself but didn't get around to do it yet (I'm starting an IT-Business as a consultant/systems programmer, see (URL) managed to run a train from an RCX with the standard power levels using (...) (22 years ago, 5-Jul-04, to lugnet.robotics.rcx.java)
 
  Re: NQC problem...driving me insane!
 
(...) You should check to make sure your light sensor is in fact changing more than 5 counts. Start by changing the above code to 2 or 3. I don't recall with NQC, but with some languages (BrickOS) the values are backwards, so you may need to check (...) (22 years ago, 5-Jul-04, to lugnet.robotics.rcx.nqc, lugnet.org.ca.rtltoronto)
 
  Re: Repairing small 9v battery box
 
(...) Hmmm, difficult. After a quick inspection, I'd say no. (...) What batteries are you using? I doubt there's many 9V batteries that can take sustained 5A for very long. ROSCO (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Re: NQC problem...driving me insane!
 
(...) Well, actually, that code works fine (running MacNQC, a fairly recent version, with 2.0 firmware). One thing to check, code-wise, is to display SENSOR_1 on the LCD, and see what the numbers are (is it set to raw mode? Is the sensor bad (I've (...) (22 years ago, 4-Jul-04, to lugnet.robotics.rcx.nqc, lugnet.org.ca.rtltoronto)
 
  NQC problem...driving me insane!
 
Hey all, I know I must be doing something very simple wrong here - but I can't for the life of me figure it out. What I'm trying to do: Have a light sensor pointed at a surface. Pass that value off to a variable (the variable then contains the (...) (22 years ago, 4-Jul-04, to lugnet.robotics.rcx.nqc, lugnet.org.ca.rtltoronto)
 
  Re: Repairing small 9v battery box
 
(...) I had a large battery box that was did not work reliably (sometimes yes, sometimes no). The problem was burning at a battery contact. The current does not need to be very high to do that if the contact area is very small. The discolored spots (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Repairing small 9v battery box
 
I've got one recently off od Bricklink, and it seems not to be working. Yes, new battery, yes, battery works in other small 9v boxes, yes, I made sure it was cool (thermal protection). Any ideas? Any suggestions how to troubleshoot or fix it, (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) Steve, no doubt you' re the best !! ;-) quite simple !! perfect!! the good thing is that it works even when program runs.... Thanks a lot (hey Steve have you the seen the gyro-bob on my site, the simplest mechanical alternative to legway: (...) (22 years ago, 4-Jul-04, to lugnet.robotics)
 
  Re: how to program the spybot remote
 
(...) don't give up. without any programming, the remote will drive the spybot. button 1 & 4 control the right motor, button 3 & 5 control the left motor. It seems messed up, but that's how it is. If the motors go the wrong way, you can switch the (...) (22 years ago, 3-Jul-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR