 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) It will help us help you if you list the resources you have and how many of these you need to make. If your resources are limited, you may have to use a few different solutions to match your inventory. Kevin (22 years ago, 20-Jun-04, to lugnet.robotics)
|
| |
 | | Re: New TLC Mindstorms survey
|
|
(...) On the software side, don't forget to lobby them to fix the #$@%$! hyperthreading USB tower driver bug!!!! I'd also love to see real C/C++ programming support out of the box -- setting up Cygwin and brickOS is just too hard for most people. If (...) (22 years ago, 20-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) bricks along the beam, like I did on my tower crane (URL) (22 years ago, 20-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
"Brass Tilde" <lego-robotics@crynwr.com> wrote in message news:00a301c4552c$24...hps.net... <snip> (...) I built something very much like this. I used a rack with a few 1x1 TECHNIC beams in it. The touch sensor pressed against the side of the rack (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: New TLC Mindstorms survey
|
|
(...) Umm - I think you guys got the wrong end of the stick there. I didnt mean bluetooth for sensor connectivity(cables do just fine), I only meant it to replace the existing IR interface for downloading programs. Although intelligent sensor nets (...) (22 years ago, 18-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | RE: is it possible to make a motor with a limited range of travel?
|
|
(...) belt. (...) Hello, If you take a beam and put racks on it, you can push that across a gear and it will make the gear spin. A back and forth motion causes back and forth rotation on the gear. To get mechanical back and forth motion, simply (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) There are some methods involving non-lego peices in the mix. One such method, is to build a touch sensor using a microswitch from a mouse. Wire this in the normally closed way - so when it is activated, it will open. So the motor will go the (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) Or you may use poor man's clutch gear: pulleys and slipping rubber belt. Or if your application does not need too much mechanical power, you can simply use a low power level on RCX output. With a power level 2 both the RCX and the motor can (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: New TLC Mindstorms survey
|
|
(...) You don't. You get it here: (URL) (22 years ago, 18-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) clutch (...) at (...) You should only need one touch sensor per rack. If you only have one motor per rack, then you should be able to use one sensor per motor (unless you have other stuff you need the sensor ports for, of course). M RRR...RRR (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|