 | | RE: is it possible to make a motor with a limited range of travel?
|
|
(...) belt. (...) Hello, If you take a beam and put racks on it, you can push that across a gear and it will make the gear spin. A back and forth motion causes back and forth rotation on the gear. To get mechanical back and forth motion, simply (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) There are some methods involving non-lego peices in the mix. One such method, is to build a touch sensor using a microswitch from a mouse. Wire this in the normally closed way - so when it is activated, it will open. So the motor will go the (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) Or you may use poor man's clutch gear: pulleys and slipping rubber belt. Or if your application does not need too much mechanical power, you can simply use a low power level on RCX output. With a power level 2 both the RCX and the motor can (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: New TLC Mindstorms survey
|
|
(...) You don't. You get it here: (URL) (22 years ago, 18-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) clutch (...) at (...) You should only need one touch sensor per rack. If you only have one motor per rack, then you should be able to use one sensor per motor (unless you have other stuff you need the sensor ports for, of course). M RRR...RRR (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
(...) Thats kinda usefull except that I dont have enough clutch gears, touch sensors or sensor inputs on my RCX :( (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: is it possible to make a motor with a limited range of travel?
|
|
Jonathan, What about putting stops on the rack to limit the travel and use a clutch gear to keep the motor from being damaged? Or what about putting a peg at each end of the rack that stick out and hit a touch sensor when the gear rack is close to (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
|
| |
 | | Re: New TLC Mindstorms survey
|
|
(...) Go to (URL) the lower left part of the page there's a picture of a cute bug-like robot with a comic strip bubble over him saying "Yes! Click here to start your LEGO MINDSTORMS survey now." Or here's the direct link... (URL) D. (22 years ago, 18-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | RE: New TLC Mindstorms survey
|
|
I'm thinking something like a hybrid between the GameboyRCX and what we have now.... What if you could use an IR equipped palmPilot (or Clie), or even a PocketPC to talk to a simple micro. Wait, you'd need an IRDA protocol stack on the micro, unless (...) (22 years ago, 18-Jun-04, to lugnet.robotics.rcx)
|
| |
 | | RE: New TLC Mindstorms survey
|
|
OK, I give up. Exactly where on the LEGO site do you get the survey? Ralph (22 years ago, 18-Jun-04, to lugnet.robotics.rcx)
|