 | | brickos with suse 9.1
|
|
I'm tying to get brickOS started on a Suse 9 System, Did anybody install brickOS and the gcc-hitachi on Suse 9 System? After I download the brick.srec to the RCX it crashes. thx KHL (22 years ago, 27-May-04, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: table brickos light to percent
|
|
In my opinion, the best way to approach this is the following: When the program starts, begin a Calibration, by first activating the light sensor, then reading the value. You can either wait a specific amount of time or have the user press a button (...) (22 years ago, 27-May-04, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: table brickos light to percent
|
|
(...) Hi Thomas, Here's the formula used in the dsensor.h include file: #define ds_scale(x) ((unsigned int)(x)>>6) //!< mask off bottom 6 bits #define LIGHT(a) (147 - ds_scale(a)/7) //!< map light sensor to 0..LIGHT_MAX This maps the raw sensor (...) (22 years ago, 27-May-04, to lugnet.robotics.rcx.legos)
|
| |
 | | table brickos light to percent
|
|
i there a table or converter from brickos light readings to light percentage ( and vice versa ) Thomas (22 years ago, 27-May-04, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
(...) A little off topic for this thread, but I thought it was worth mentioning: The microscout can be controlled by a spybot as well. The spybot has both IR comms and VLL I/O. So a spybot has two built in motors and can control a microscout for a (...) (22 years ago, 26-May-04, to lugnet.robotics)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
Basicly, you can use the Microscout as an extra motor (but of course you're blowing away a motor port to do it! The ms_Fwd and ms_Rwd commands have an unavoidable delay in between them, so you can't get the motor to run continuously (not that I'm (...) (22 years ago, 26-May-04, to lugnet.robotics)
|
| |
 | | IR Range Finders on CyberMaster
|
|
If anyone is interested, it is possible to use the MindSensors separately powered SHarp GPD12 IR range finders on the CyberMaster. These range finders require a motor port to power them, and also connect to sensor port. Connecting them to the (...) (22 years ago, 26-May-04, to lugnet.robotics.cybermaster)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
(...) Hi Mark, here's a program in Mindscript for your RCX that will exercise the Microscout a bit: program RCX2MS { #include"rcx2.h" #include"rcx2vll.h" main { vll_begin(B) forever { ms_Fwd(B) ms_Fwd(B) ms_Fwd(B) ms_Rwd(B) wait 200 // 2 seconds } } (...) (22 years ago, 26-May-04, to lugnet.robotics)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
(...) No - they can't. They use visible light - not IR. (...) Nothing interesting! (...) 'P' mode is how you program them - but not from the RCX. (...) Yes - you can use the USB tower - it has both a visible light AND an IR light. But the older (...) (22 years ago, 26-May-04, to lugnet.robotics)
|
| |
 | | Re: RCX and Micro Scout Communication
|
|
Here are a couple answers for you... (...) I THINK you can program a Micro Scout using the USB tower. The 1.5 & 2.0 sets come with a fiber-optic cable that you can use. (...) Here's a page with more info about VLL (URL) (...) Hope that helps Steve (22 years ago, 25-May-04, to lugnet.robotics)
|