To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *37659 (-10)
  Re: gear pulley/release system
 
(...) How about using a caster wheel? I used it for a jumping mechanism, but I think it can also be adapted for a cannon like you describe. Using 1 motor, it keeps firing over and over (URL) (23 years ago, 20-Jun-03, to lugnet.robotics, FTX)
 
  Re: Switching Direction
 
(...) I tried it and it works for me :-) On an unrelated note am I right in thingking the only way to get the file "afxdtctl.h" would be to upgrade to Visual c++ Ver 6? Steve (23 years ago, 19-Jun-03, to lugnet.robotics)
 
  Re: 8455 - new form factor for large piston and switches
 
(...) Rob, Nope. Only large pistons. There is no performance difference between the pre-2003 pistons and the 2003 pistons. Form factor is the only difference. (...) The resistance to flipping is the same between virgin old style and virgin new style (...) (23 years ago, 19-Jun-03, to lugnet.robotics)
 
  RE: 8455 - new form factor for large piston and switches
 
Kevin, Did 8455 come with small pneumatic cylinders, or just large ones? Does the new switch have better, worse, or comparable action to the old switch, in your opinion? Thanks, Rob (...) (URL) new form factor switch is side by side with its (...) (23 years ago, 19-Jun-03, to lugnet.robotics)
 
  Re: All Lego Ack Circuit for LDCC
 
(...) indeed, the construction of this beast may be very different (e.g. metallic contact, 0 resistance... and a lot of bounce almost completely avoided with conductive rubber) Philo (23 years ago, 19-Jun-03, to lugnet.trains, lugnet.robotics.rcx)
 
  Re: Error linking c++ with gcc 3.3
 
No, I'm sorry, it doesn't seem to quite work. But it does get rid of the 3 errors at the bottom - Now it's just the operator new/delete stuff. I replaced the stub.c with the thing below, made libc++.a, and just make in lib/c++, and then go to demo (...) (23 years ago, 19-Jun-03, to lugnet.robotics.rcx.legos)
 
  Re: Switching Direction
 
----- Original Message ----- From: "Steven lane" <steveroblane@aol.com> To: <lego-robotics@crynwr.com> Sent: Wednesday, June 18, 2003 2:29 PM Subject: Switching Direction (...) sensor to (...) up. (...) and (...) the (...) round. (...) motor (...) (...) (23 years ago, 19-Jun-03, to lugnet.robotics)
 
  Re: All Lego Ack Circuit for LDCC
 
Thanks Philippe, I wasn't sure of the characteristics of the Cybermaster touch sensors. Also, I didn't want anyone thinking it was OK to use this guy: (URL) checking the resistance (yeah, I know it looks different, but you never know... :-) Mark (...) (23 years ago, 18-Jun-03, to lugnet.trains, lugnet.robotics.rcx)
 
  gear pulley/release system
 
I have looked all over the forums and archives and still have not found quite what I am looking for. A cocking mechanisim for a cannon. I need a 1x16 beam (the 'bolt', held by rubber bands) to be pulled back and released down an 2x16 chamber pushing (...) (23 years ago, 18-Jun-03, to lugnet.robotics)
 
  Re: 8455 - new form factor for large piston and switches
 
Kevin L. Clague's utterance expressed in news:HGnFFq.yoC@lugnet.com: (...) well. the studs will be missed for my part - but then again... in applications where rotation is needed they are definetely better than the old ones - doesn't require as much (...) (23 years ago, 18-Jun-03, to lugnet.technic, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR