 | | Re: Error linking c++ with gcc 3.3
|
|
No, I'm sorry, it doesn't seem to quite work. But it does get rid of the 3 errors at the bottom - Now it's just the operator new/delete stuff. I replaced the stub.c with the thing below, made libc++.a, and just make in lib/c++, and then go to demo (...) (23 years ago, 19-Jun-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Switching Direction
|
|
----- Original Message ----- From: "Steven lane" <steveroblane@aol.com> To: <lego-robotics@crynwr.com> Sent: Wednesday, June 18, 2003 2:29 PM Subject: Switching Direction (...) sensor to (...) up. (...) and (...) the (...) round. (...) motor (...) (...) (23 years ago, 19-Jun-03, to lugnet.robotics)
|
| |
 | | Re: All Lego Ack Circuit for LDCC
|
|
Thanks Philippe, I wasn't sure of the characteristics of the Cybermaster touch sensors. Also, I didn't want anyone thinking it was OK to use this guy: (URL) checking the resistance (yeah, I know it looks different, but you never know... :-) Mark (...) (23 years ago, 18-Jun-03, to lugnet.trains, lugnet.robotics.rcx)
|
| |
 | | gear pulley/release system
|
|
I have looked all over the forums and archives and still have not found quite what I am looking for. A cocking mechanisim for a cannon. I need a 1x16 beam (the 'bolt', held by rubber bands) to be pulled back and released down an 2x16 chamber pushing (...) (23 years ago, 18-Jun-03, to lugnet.robotics)
|
| |
 | | Re: 8455 - new form factor for large piston and switches
|
|
Kevin L. Clague's utterance expressed in news:HGnFFq.yoC@lugnet.com: (...) well. the studs will be missed for my part - but then again... in applications where rotation is needed they are definetely better than the old ones - doesn't require as much (...) (23 years ago, 18-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: All Lego Ack Circuit for LDCC
|
|
(...) All touch sensors I measured have a "pressed" resistance between 400 and 600 ohms (depends on touch sensors and on pressure, more pressure meaning lower resistance). Actually there is no separated resistor, you get the internal resistance of (...) (23 years ago, 18-Jun-03, to lugnet.trains, lugnet.robotics.rcx)
|
| |
 | | Re: Switching Direction
|
|
(...) I stumbled on this one a few days ago... and ended up with a if(variable)/OnFwd/else/OnRev construction :c( Philo (23 years ago, 18-Jun-03, to lugnet.robotics)
|
| |
 | | Switching Direction
|
|
I have a motor which drives a rack mechanism and I'm using a rotation sensor to index my position on the rack. When I program the motor (in NQC) to go forward I want the sensor to count up. If the sensor then actually goes down I want to test for (...) (23 years ago, 18-Jun-03, to lugnet.robotics)
|
| |
 | | Re: 8455 - new form factor for large piston and switches
|
|
Kevin, This is the new backhoe you're talking about, correct? These pistons are from that set? Before you accidentally lose a few pieces, how about doing a Peeron inventory? ;-) (23 years ago, 18-Jun-03, to lugnet.robotics)
|
| |
 | | Re: Error linking c++ with gcc 3.3
|
|
(...) You should add -fno-rtti -fno-exceptions to the CXXFLAGS in Makefile.common. To get rid of the operator new/delete errors you can replace lib/c++/stub.c with a stub.cpp containing the following. Don't forget to update the Makefile. This works (...) (23 years ago, 18-Jun-03, to lugnet.robotics.rcx.legos)
|