 | | Re: Increase touch sensor sensitivity?
|
|
(...) No, they are essentially switches that are either on or off. Though the whole truth is that they are made from conductive rubber, and that they go from off to on over a very small distance. I once measured this by an arrangement that very (...) (24 years ago, 7-May-03, to lugnet.robotics)
|
| |
 | | Re: TIME STAMP for a LNP distributed robot
|
|
BTW, make sure you include: #include <time.h> Otherwise, get_system_up_time() will only return 16 bits! Mark (24 years ago, 7-May-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: TIME STAMP for a LNP distributed robot
|
|
Hi, The sys_time variable is the basic timekeeper for BrickOS. It is a 32-bit integer that is incremented every millisecond by the kernel. In older versions of the kernel you could access the variable directly, however, in 0.2.6.10 and later you (...) (24 years ago, 7-May-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Dr. Vegetable's Virtual Remote
|
|
I have just released a freeware utility program for Windows that emulates the MindStorms infrared remote control using a USB or RS-232 IR tower. The program supports all functions of the remote and does not require any other support software to be (...) (24 years ago, 7-May-03, to lugnet.robotics.rcx) !
|
| |
 | | TIME STAMP for a LNP distributed robot
|
|
Hi, I'd like to make a basic implementation of a time stamp on a distributed schame, using Lamport's algorithm. It states basically that when a node receives a message, it get the time stamp that's contained on it, and compares with it's own, if the (...) (24 years ago, 7-May-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Increase touch sensor sensitivity?
|
|
(...) I (...) if (...) Try turning the logic around. Keep the sensor engaged the sensor *until* the ground falls off instead of engaging it *when* the ground falls off. In other words, the lever arms would fall away from the sensor when there is no (...) (24 years ago, 7-May-03, to lugnet.robotics)
|
| |
 | | Increase touch sensor sensitivity?
|
|
Hello all, I am attempting to my first mobile lego robot using the lego SDK 2.0 software. Im running into problems using the touch sensor to detect a lack of ground ahead of the robot. Im simply using two lever arms that "fall" into the touch sensor (...) (24 years ago, 7-May-03, to lugnet.robotics)
|
| |
 | | Vision command and night vision
|
|
Couple months ago I have seen VC camera modified to see even in complete darkness using IR LED diodes mounted around it. Today i tried to find it again but Lugnet search didn't give me any positive results. Does anybody know location of the page I (...) (24 years ago, 7-May-03, to lugnet.robotics.vc)
|
| |
 | | Spybotic Mods
|
|
I have Snaptrax S45 and a Gigamesh G60 Spybotics robots. I recently modded them both. The 1st mod was easy, I added powerful magnets on the bottom of each robots using double-sided tape so that when I am working on my techbench area if I drop a (...) (24 years ago, 7-May-03, to lugnet.robotics.spybotics)
|
| |
 | | Re: brickos-0.2.6.10 .text is not within region ram
|
|
(...) Dear Mark I will check the demo programs and more stuff. If i'm not wrong it looks to me that now we have 16K for the kernel ( c000-b000) = 4Kb more. If i got the results, i'm coming back to the forum. best regards Bernhard (24 years ago, 7-May-03, to lugnet.robotics.rcx.legos)
|