 | | Problems after upgrading from brickos 0.2.6.09 to 0.2.6.10
|
|
Hello, I hope somebody could help me with the following problem. So far I was using brickos 0.2.6.09 under Windows XP and everything worked fine. I downloaded version 0.2.6.10 and downloaded it's brickos.srec file to the RCX. As soon as I switch on (...) (24 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: baby walker
|
|
after watching that film, i got to say that this is fun but its totally not a walker. first foremost for that leg drag, I'd rename this Igor or somthing. -tk "Philippe Hurbain" <philohome@free.fr> wrote in message news:HCvtts.nF@lugnet.com... (...) (...) (24 years ago, 5-Apr-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: baby walker
|
|
...and then they were five... The 1x7 liftarm is a bit short and the motor bumps against the flexible axle. So I used a 1x9 (7+2) to be low enough, and I could remove Micromotor bottom. I used a 1x2 liftarm with plate only for aestetical reasons... (...) (24 years ago, 5-Apr-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: BrickOs Problem (again)
|
|
(...) Cygwin is pure Windows. DJGPP is DOS, and doesn't work well with brickOS. Although everyone should use Linux. DJGPP and brickOS: I managed to build binutils under djgpp, gcc failed but is probably fixable. However, djgpp doesn't have POSIX (...) (24 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Lego motor reverse with 2 switches
|
|
You could make a half H-bridge: --------| i---...---| i---...--- | | | | | | / Motor / | | | ---...--- Remember that you have to program a dead time between the switches so as not to short the batteries. You could also make a full H-Bridge, using (...) (24 years ago, 5-Apr-03, to lugnet.robotics)
|
| |
 | | Re: baby walker
|
|
(...) Cool! I figured that the stiffness of the wire would help. I guess I'll call it Shorty ,as it's only a little over an inch tall :). Now I've just got to get that micro motor ordered so I can try it out myself. I'm wondering if you could try (...) (24 years ago, 5-Apr-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: baby walker
|
|
It works! (URL) stability is obtained more from wire stiffness than from 2x4 brick (not heavy enough, without wire motor would turn over when in topmost position) Cheers, Philo www.philohome.com (...) (24 years ago, 5-Apr-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Lego motor reverse with 2 switches
|
|
I built a lego robot, I am using linux as operating system. I also have a simple circuit connected to the printer port that has 4 switches. (I can activate or deactivate 4 circuits) . My robot has 2 motors, and i need to forward or reverse each of (...) (24 years ago, 5-Apr-03, to lugnet.robotics)
|
| |
 | | Re: BrickOs Problem (again)
|
|
(...) You didn't install tar. Run Cygwin setup again and add tar. (...) No, incorrect. (...) No, he needs to install tar. Max. (24 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: BrickOs Problem (again)
|
|
(...) Hello, I think it's really hard to install brickOS on XP cause Cygwin is on a dos base (no ?) and XP have no DOS (only emule). To solve you problem you should install linux :-P Seriously : if cygwin don't find tar you should try to search (...) (24 years ago, 5-Apr-03, to lugnet.robotics.rcx.legos)
|