To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *36714 (-10)
  incremental encoders
 
Hi all, Can anyone tell me where I can find low cost incremental encoders. As part of my robotics research project, I have interfaced a DGPS receiver for navigating the mobile robot. I want to use the encoders to in\mprove system resolution and know (...) (24 years ago, 20-Feb-03, to lugnet.robotics)
 
  Re: RIS only rack-and-pinion steering car
 
Hey! Very cool. I did a similar thing (though decidedly simpler) for a Syngress book a while back. It was an "F1 Racer" though really it just looked like a big open car and since we were limited to the RIS kit for this book, it was also a Rack and (...) (24 years ago, 20-Feb-03, to lugnet.robotics)
 
  Re: BricxCC on Win XP how
 
(...) Wow, key tips, great questions, fun links, thanks again for leading me into hours of enlightening experimentation. As a newbie, I'm surprised to think I see nqc reports port in use by exiting immediately without complaint, and BricxCC reports (...) (24 years ago, 20-Feb-03, to lugnet.robotics.rcx)
 
  Re: Robotics round table at BrickWest
 
(...) Because the animation festival and closing/awards ceremony went quite late the night before, and the robotics round table was scheduled early the next morning, we ended up starting fairly late, and not too many people showed up. (I have a (...) (24 years ago, 20-Feb-03, to lugnet.robotics, lugnet.events.brickswest)
 
  New robotics book by Eric Wang
 
New book "Engineering with LEGO Bricks and RoboLab" by Eric Wang. See (URL) . Sample at (URL) More info at (URL) . (24 years ago, 19-Feb-03, to lugnet.edu, lugnet.robotics.rcx.robolab, lugnet.robotics.edu)
 
  Robotics round table at BrickWest
 
I am interested in the discussion at the robotics round table at BrickWest 2003. What type of ideas, themes, issues were discussed? -- Ed Manlove emanlove@eclipse.net (24 years ago, 19-Feb-03, to lugnet.robotics, lugnet.events.brickswest)
 
  6 speed+Reverse Transmission Update
 
I have completed my 6 speed+Reverse transmission, and these are the specs: -0.54:1 ratio -width only increases by 2 or 3 studs (not quite sure yet-probably 2) -6th gear slot fits easily on top So the lows are the width increses and the ratio is (...) (24 years ago, 19-Feb-03, to lugnet.technic, lugnet.general, lugnet.modelteam, lugnet.robotics)
 
  Re: BricxCC on Win XP how
 
(...) Which COM port is RIS using? Can you describe exactly what BricxCC says/does when you try to get it to find your brick? Does the tower light come on at all? As was suggested already, try choosing the same COM port that RIS uses rather than (...) (24 years ago, 18-Feb-03, to lugnet.robotics.rcx)
 
  Re: BricxCC on Win XP how
 
(...) Did you try to fix communication port instead of using automatic configuration ? On my machine (Win2000) where I have both a serial Spybotics cable and a RIS USB tower, I have to specify the port that BricxCC must use. Philo www.philohome.com (24 years ago, 18-Feb-03, to lugnet.robotics.rcx)
 
  Re: BricxCC on Win XP how
 
Pat For what its worth, BricxCC (latest version) works 100% fine with my Win XP setup. I am however using it with a Spybot and the included serial cable. Good luck with it Regards Philip "Pat LaVarre" <ppaatt@aol.com> wrote in message (...) (24 years ago, 18-Feb-03, to lugnet.robotics.rcx)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR