 | | Re: New Parts
|
|
(...) One new part that I'm happy to finally see is a 7-long axle! There's a light gray one in <set:8355>, and perhaps some of the other new racers as well. -- David Schilling (24 years ago, 14-Jan-03, to lugnet.technic, lugnet.robotics, lugnet.modelteam)
|
| |
 | | Re: New Parts
|
|
(...) parts to see if they can solve a particular problem. However they tend to create $$ problems instead :) (...) I will! /Tobbe (24 years ago, 14-Jan-03, to lugnet.technic, lugnet.robotics, lugnet.modelteam)
|
| |
 | | Re: Interesting BrickOS Timing Results
|
|
Mark, ANOTHER great find! You are pushing BrickOS to new heights! Ok, so what can we do about this? 1) Provide a constant to set the update frequency at compile time. 2) Provide a variable to set the update frequency at run time. 3) Optimize the (...) (24 years ago, 14-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Interesting BrickOS Timing Results
|
|
Oops, found a little bug. ;-) Forgot to turn off the rotation sensors. Caused a wrong reading if you let the program run through the readings more than once. The rotation sensor section should read like this: // with two rotation sensors enabled (...) (24 years ago, 14-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Interesting BrickOS Timing Results
|
|
Hi All, The recent posts about interfacing an i2c device to an RCX sensor port (in .robotics) got me interested in looking at the kernel code that handles the sensors. So, I did and found myself looking at the ds_handler function. This function is (...) (24 years ago, 14-Jan-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Land mine robot
|
|
(...) Since this is a school project - we shouldn't be telling you how to do it, we should be pointing you towards ways to search for a solution yourself. So... This requires a logical approach (and that always looks good in a school report!) Now - (...) (24 years ago, 14-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Land mine robot
|
|
I'm a Senior in high school and one of the requirements to graduate is that we must complete a Senior project. I know nothing about building sensors or electronics at all. All though I could learn very easily. The purpose of the post was to find (...) (24 years ago, 14-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Land mine robot
|
|
(...) I've been using mine in sand, dirt, middle of the street, etc. for years and haven't had any serious problem. Just be sure to clean everything when you're done. Warm water and gentle dish detergent is what I suggest (don't do the motors (...) (24 years ago, 14-Jan-03, to lugnet.robotics)
|
| |
 | | Re: Hi, I'm new
|
|
"Tjandra J" <lego-robotics@crynwr.com> wrote in message news:046601c2bad2$44...Tjandra... (...) with (...) Check out this site. Look in the "Gallery" (URL) walkers are a real challenge. Good luck with your project. -- Bob Fay (URL) (24 years ago, 13-Jan-03, to lugnet.robotics)
|
| |
 | | Re: RCX Motor Controller
|
|
"Carson Au" <carsonau@excite.com> wrote in message news:H8oBI4.7o2@lugnet.com... (...) The RCX uses Pulse Width Modulation to control the motors. -- Bob Fay (URL) (24 years ago, 13-Jan-03, to lugnet.robotics)
|