 | | Pre-Announcing Off-Road RC Racing Competition at BricksWest 2003
|
|
I am going to be holding an Off-Road RC racing competition at BricksWest 2003. It will still take me a few days to get the rules together, but I thought that with the $99 8475's available at Amazon, (see (URL) I'd give people the heads up, so that (...) (24 years ago, 14-Dec-02, to lugnet.events.brickswest, lugnet.technic, lugnet.robotics)
|
| |
 | | Re: Shufflebot Concept
|
|
The problem with that is you'd have to put the mechanisms together by putting axles over the first setup, which begins looking ugly. This is how I achieved the first walking part: 1. Geared down motor going to two output axles. 2. Put two pulleys on (...) (24 years ago, 13-Dec-02, to lugnet.robotics)
|
| |
 | | Re: Shufflebot Concept
|
|
(...) Well, if you can do one, how about if you put two of these right next to each other? I'm sure you'd want one to be a mirror of the other, to put them closer together... I don't know if three would work as well. Maybe you could have one that's (...) (24 years ago, 13-Dec-02, to lugnet.robotics)
|
| |
 | | Re: sys_time (long post)
|
|
(...) I went back and read... I was missing something apparently... Note to self... do not skim. -Kekoa (24 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: sys_time (long post)
|
|
Does the H8 let an interrupt interrupt an interrupt? (Or at least the interrupts that matter in this case?) You two might want to check on that. It would seem the code is safe if the answer to the first question is no... ? Maybe I'm missing (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Shufflebot Concept
|
|
Is there any way to make a shuffling (stompbot) drive where three shufflers are used on each side. When one goes up, the other two go down, and when those two go up the other one goes down. This is used to provide locomotion. The best example of (...) (24 years ago, 13-Dec-02, to lugnet.robotics)
|
| |
 | | RE: Firmware download troubles
|
|
The size of the firmware isn't going past the 0xcc00 boundary, is it? The firmware in the RCX only does a sum on the bytes up to 0xCBFF in the downloaded firmware, as far as I recall... Cheers, Ralph (24 years ago, 13-Dec-02, to lugnet.robotics.rcx)
|
| |
 | | Re: BrickOS Threading...
|
|
Joe, (...) Maybe a special kernel build for testing purposes that increments the lower sys_time word by 0x4000 instead of 1. This will greatly increase the opportunity for this glitch to occur (from once every 65 seconds to once every 4ms.) You (...) (24 years ago, 13-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Hammer Help
|
|
Thanks for the response. I've decided to stay away from string on the robot as string can get easily entangled, especially if battling another robot. I took a break from trying a design using gears and differentials - I was getting really (...) (24 years ago, 13-Dec-02, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: Hammer Help
|
|
In the prototype I used string and winch to set the hammer. I've decided not to use it on the robot - string can too easily get caught and entangled in stuff, especially if it goes up agianst another robot. On the prototype it works surprisingly (...) (24 years ago, 13-Dec-02, to lugnet.robotics)
|